Sangean HDT-1 - Manual

5 Main Unit Controls (Rear) 13. 14. 15. 16. External FM antenna socket External AM loop antenna socket Line Out socket SPDIF Optical Connection (Optional on HDT-1X) AC power cord socket 17. 18. 20070425_HDT-1&HDT-1X_381R20S-A.p65 2007/4/30, ¤U¤È 01:43 8

6 Accessories Detachable power Cord x 1 FM Dipole Antenna x 1 AM Loop antenna x 1 20070425_HDT-1&HDT-1X_381R20S-A.p65 2007/4/30, ¤U¤È 01:44 9

8 Getting started Step 1. Inspect package to insure that all parts & accessories are included. Step 2. Find a proper location for your new HDT-1/HDT-1X HD Radio Tuner following the guidelines on table 1.1. Step 3. Connect the included or other external FM antenna to Figure 2, #13. Step 4. Connec...

9 Navigating the Display There are many display functions. This will help you understand what the display is telling you, making navigation and setup easier. (A)Radiotext, (B)Time, (C)Signal quality, (D)Frequency, (E)and Audio spectrum. : RDS Indicator : Program Station : Program Type : Callsign : R...

10 Setting up and Programming your HDT-1/HDT-1X Setting the clock Clock setting can be done when the tuner is in Standby (power off)1. Press and hold “INFO” button for approx. 2 seconds until display flashes “clock set “to enter Clock Set mode.2. Press Tuning UP or Down button to select AM or PM.3. ...

11 Radio Controls To turn the radio on, press the Standby button. Pressing the Standby button again will put the unit into standby. In standby, the tuner will display the time, dim the backlight and standby LED will be on. Selecting the radio band Press the BAND button to select the appropriate band...

14 Seek Function To seek to another clear station, use the SEEK toggle button. Press and release the SEEK UP or DOWN will go to the next available station with good signal. Press any key to stop SEEK function. Using AM and FM presets Preset stations There are 20 preset stations for FM (10 x FM1, 10 ...

15 Recall preset stations To recall preset stations, select required band by pressing BAND selection button. Press PRESET button to enter PRESET recall mode. Display will show “GO TO PRESET”. Then followed by using one of the following methods to recall the stations. 1. Press and release the number ...

16 Advanced Information Long press INFO button for 2 seconds to enter Advanced Information. Press and release INFO button will cycle through information of RESET, LCD Contrast Adjust, Backlight Brightness Control, (For HDT-1X: Stereo/Mono Mode, Analog Mode, Split Audio Mode), Bit Error Rate, The car...

17 Advanced Menu Options Menu Option Backlight Mono/Stereo Mode Analog Mode (HD OFF) Split Audio Mode Bit Error Rate Carrier to Noise Ratio Fuse Bit Check Transmission Mode Station ID Software Version Controls Tuning Up to activate option Tuning Down to deactivate Tuning Up to activate option Tuning...

18 Troubleshooting Issue Power Won’t Turn On Remote Doesn’t Work I don’t hear any audio I only hear audio in one speaker I only hear static Poor audio quality Possible Solutions Check AC power cord connection Check circuit breakers/fuses Call Sangean Service Department at 888-SANGEAN Remove plastic ...

20 Specifications Power: Mains: AC 120 Volts 60 Hz only, 10 Watt maximum Battery ( remote control ): 3.0V CR 2025 Frequency coverage: FM 87.50 - 108.10 MHz AM 520 - 1710 kHz HD FM 87.50 - 108.10 MHz HD AM 520 - 1710 kHz Antenna System: FM - Dipole type ( supplied ) AM - Loop type ( supplied ) Dimens...

21 HDT-1/HDT-1X Brief User Interface: UI KEY function NO 1 2 3 4 5 Button standby Band Info Info Info Action short short short long 2s (To use info key to jump next status) short(To use number key and tune select clock time, then to press Info button finish setting) long 2s(To use info key to jump n...