Samsung VR50T95735WSA - User Manual

P REP ARA TION • Do not operate the vacuum in a room where an infant or child is sleeping.• Do not operate the vacuum in an area where there are lit candles or fragile objects on the floor. • Do not operate the vacuum in a room that has lit candles on furniture that the vacuum may accidentally hit o...

P REP ARA TION Jet Bot • Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc. • Do not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on. • Do not put any objects into o...

P REP ARA TION Power related WARNING • Please prevent any risk of electric shock or fire. – Do not damage the power cord. – Do not pull the power cord too hard or touch the power plug with wet hands. – Do not use a power source other than Rated volatge of charger and also do not use a multi-outlet t...

P REP ARA TION • Be sure the Jet Bot does not suck in or touch any kind of liquids (water, beverage, filth, etc.). – The Jet Bot can be severely damaged and it may contaminate other areas if the wheels pass through liquid. • Do not spill any liquids on the Clean Station. – There is a risk of fire or...

P REP ARA TION In use WARNING • If any abnormal sounds, smells or smoke come from the Jet Bot, immediately shut off the power switch of the Jet Bot and contact a service center. CAUTION • Using the Jet Bot on a thick carpet may damage both the Jet Bot and the carpet. – The Jet Bot cannot pass over a...

P REP ARA TION Cleaning and maintenance WARNING • When the power cord is damaged, contact a service center to get it replaced by a certified repairman. – There is a risk of fire or electric shock. • Please check with a SAMSUNG Electronics service center when replacing batteries. – Using batteries fr...

INSTALLA TION INSTALLATION Installing a Clean Station Approximately 0.5 m Approximately 0.5 m Status Indicator Approximately 1 m 1 Connect the provided power cord to the bottom of the Clean Station. 2 Position the power cord into the fixing groove at the rear of the Clean Station. 3 Place the Clean ...

OPERA TION Charging the Jet Bot Before using the Jet Bot for the first time, charge it completely. (For the charging time and cleaning time, refer to the ‘Product specification’.) OFF ON 1 Remove the yellow gasket attached to the power switch at the side of the Jet Bot and press the power switch to ...

OPERA TION Auto charging The Jet Bot automatically returns to the Clean Station when it completes cleaning or when the battery is low to recharge. Docking (Recharging) You can return the Jet Bot to the Clean Station while cleaning to recharge. • Press the [ ] on the Jet Bot or use the SmartThings Ap...

OPERA TION Checking if the docking (recharging) does not work Check the Clean Station’s installation status • Check whether the Clean Station has been installed in a place where the Clean Station cannot guide the Jet Bot to return. • Check whether the distance between the Clean Station and the Jet B...

OPERA TION Using the Jet Bot Before using the Jet Bot, press the power switch at the side of the Jet Bot to turn the Jet Bot on. ❇ ❇ For the normal use of the Jet Bot’s functions, the SmartThings connection is required. – For downloading and installing the SmartThings App, refer to the ‘SmartThings ...

OPERA TION Operation status on the LED Status Indicator Classification Color Meaning Jet Bot While operating Red Blinking without moving An error occurs. Blinking while moving Auto returning to the Clean Station due to low battery On Operating stops due to low battery Blue Monitoring While charging ...

OPERA TION Cleaning Functions Cleaning Functions Operation Cleaning Methods • Auto Clean: Cleans automatically until the Jet Bot completes cleaning one time. • Room Clean: You can select a room you want to clean.• Around Furniture Clean: You can select the areas around furniture or an electronic app...

OPERA TION ❇ ❇ When the Jet Bot does not have a saved map, it studies cleaning space through Auto Clean function which starts from the Clean Station. After studying the cleaning space, a map is saved. (The map creation is enabled through the SmartThings App only.) ❇ ❇ You can edit or delete the map ...

OPERA TION NOTE • When a Check Notice occurs or when you carry the Jet Bot to another place and start cleaning, the Jet Bot spins left and right at a 30 degree angle to recognize its location before it starts cleaning. • If the Jet Bot cannot recognize its current location, it does not start a set c...

OPERA TION Parts diagram Jet Bot 11 04 10 01 12 04 01 08 07 06 09 02 04 05 03 Top 01 Obstacle Sensor 02 Power switch 03 Upper Cover 04 Docking Sensor Window 05 LiDAR Sensor 06 Fine dust Filter 07 Dustbin 08 Start/stop button 09 Docking (Recharging) button 10 Status Indicator 11 Camera 12 3D Sensor 0...

MAINTENANCE Cleaning the Jet Bot Before maintenance work, you should turn off the power switch at the side of the Jet Bot. Emptying and cleaning the Dustbin 1 Detach the upper cover using the groove under the cover. 2 Hold the Dustbin handle and lift the Dustbin up. 3 Unlock the transparent clip at ...

MAINTENANCE 7 Attach the filter to the Dustbin. 8 Attach the Upper Cover and the Lower Cover to the Dustbin. Make sure you can hear them click into position. 9 Attach the Dustbin to the Jet Bot. Grasp the handle and put the Dustbin into both grooves. Cleaning the Driving Wheel 1 Place a soft cloth d...

MAINTENANCE Cleaning the brush 1 Push the Brush Cover Lock upward to unlock. 2 Detach the brush cover. 3 Lift up the left side of the brush first and then pull the brush from the groove on the right. 4 Clean the brush. 5 Attach the brush. 6 Attach the brush cover. English 25 VR9500_EN_00846J-02_SA.i...

MAINTENANCE Cleaning the Sensor Window Wipe the Sensor Window with a soft cloth. Obstacle Sensor 3D Sensor Docking Sensor Window Camera LiDAR Sensor Cliff Sensor Dust Sensor Window Cleaning the Fine dust Filter For detailed methods of use and cleaning, refer to the QR code. English 26 VR9500_EN_0084...

MAINTENANCE Cleaning the Clean Station Before cleaning the Clean Station, unplug the power cord from the electrical outlet. Replacing the Dust Bag 1 Press the [PUSH] button on the top of the Clean Station to open its cover. 2 Pull the top of the Dust Bag holder gently. – If you do not pull the Dust ...

MAINTENANCE Cleaning the bottom cover 1 Lay the Clean Station on its side and turn the 7 fixed screws on the bottom cover in the unlock direction( ). 2 Detach the cover and remove dirt. 3 Clean the cover with water and dry it completely in the shade. 4 Attach the cover to the Clean Station. 5 Turn t...

APPENDIX SmartThings App The SmartThings App is only compatible with models that have a Wi-Fi function.If you do not have a Wi-Fi router, you cannot use the SmartThings App. Setting up the wireless router • Please refer to the user manual of your wireless router for the settings of the wireless rout...

APPENDIX Downloading the SmartThings App • Download and install the SmartThings App from the markets (Google Play Store, Apple App Store, or SAMSUNG Galaxy Store). To find the app, use the keyword “SmartThings”. NOTE • SmartThings is incompatible with some tablets and some mobile devices.• Some iPad...

APPENDIX 4 [Android] The connection to your device will be progressed automatically. – [iOS] Open the setting app, and select [vacuum]_E30AJT** in the Wi-Fi list. 5 Provide the authentication when you are directed to do so. 6 [Android] The connection to your wireless router will be progressed automa...

APPENDIX Functions of the SmartThings App Classification Functions Explanation Monitoring Cleaning Report • You can check the result of the last cleaning.• You can check the histories of last 50 cleanings. Home Monitoring • The Home monitoring feature utilizes a camera on the front of the Jet Bot so...

APPENDIX Installation NOTE • Install the Clean Station in a place where the floor and wall are level.• If the cleaning area is wooden floors, it is best to install the Clean Station along the grain of wooden floors. • If the power switch is off, the Jet Bot will not charge even if it is docked on th...

APPENDIX • If the Jet Bot is left detached from the Clean Station, the battery will drain naturally. – Try to keep the Jet Bot being charged on the Clean Station. (However, turn off the power switch and leave the Clean Station unplugged when planning to leave the house for long periods of time by go...

APPENDIX Battery usage NOTE • When you purchase a battery, check the SAMSUNG logo ( ) attached on the battery and the model name, then contact a service center. • This battery is exclusively for the SAMSUNG Electronics Jet Bot. Do not use it for any other products or purposes. • Do not disassemble o...

APPENDIX Corrective measures before reporting a problem 1 The Status Indicator turns red and blinks with a voice guide. 2 Turn off the power switch and check the instructions below and take appropriate actions. 3 When turning the Jet Bot on by pressing the power switch, the Status Indicator turns wh...

APPENDIX Troubleshooting Symptom Checklist The Jet Bot is not working at all. • Check if the power switch is on.• Check if the Status Indicator is on.• Check if the Jet Bot's battery is depleted. – When the Jet Bot’s Status Indicator turns red and stays red, place the Jet Bot manually on the Clean S...

APPENDIX Open Source Announcement The software included in this product contains open source software. To obtain the source code covered under licenses which have the obligation of publishing source code (e.g. GPL, LGPL… etc), please visit http://opensource.samsung.com/ and search by model name. It ...

APPENDIX Product Specification Classification Items VR50T95**** series Mechanical specifications Weight 4.4 kg Size W 305 mm x  D 320 mm x H 120* mm (*Including LiDAR sensor: 136.5 mm) Cleaning method LiDAR location recognition Button method of the Jet Bot Touch type Electrical specifications Power ...