Page 2 - Safety Regulations
SHR-2040/2041/2042 USER’S MANUAL ii Please be sure to keep the following in mind for the right use of the product to pre-vent proprietary risk or damage. ■ Do not use multiple plugs at once. ● This may cause abnormal heat generation or fire ■ Do not put a vase, flowerpot, cup, cosmetics, medicine, o...
Page 3 - WARNING; Before we start; Standards Approvals; Note
iii WARNING [Battery] As wrong exchange of the battery in SHR-2040/2041/2042 may cause explosion, youshall use the certified battery for SHR-2040/2041/2042. The battery specification is as follows. -Normal Voltage: 3V-Normal Capacity: 220mAh-Continuous Standard Load: 0.2mA-Operating Temperature: -30...
Page 4 - Contents
iv Safety Regulations Before we start Standards Approvals Chapter 1 Overview 1. Introduction 2. Features 3. Part Names and Functions Chapter 2 Installation 1. Installation Environment Setup 2. Checking Product & Accessory 3. HDD Addition Chapter 3 Connecting with Other device 1. Connecting Video...
Page 5 - Chapter 5 Menu Setup; Chapter 6 PTZ Camera Control; Chapter 7 Recording; Chapter 8 Search and Play
v Chapter 5 Menu Setup Before Use 1. System 2. Camera 3. Monitoring 4. Recording Mode 5. Event Record Mode 6. Record Schedule 7. Backup 8. Network 9. Network Setup Chapter 6 PTZ Camera Control 1. PTZ camera Control Mode 2. Basic Operation of PAN, TILT, & ZOOM 3. Preset Setup 4. Camera Menu Setup...
Page 8 - Introduction
1 Introduction 1-1 The Digital Video Recorder(DVR) compresses the 4 channel of camera input data into theMPEG4 video file and the 4 channel of voice input data into the ADPCM audio file in the realtime to record them in the Hard Disk or retrieve them from the Hard Disk simultaneously.In addition, it...
Page 9 - Features
2 Features 1-2 ■ 4 CH Composite Input Connectors ■ NTSC / PAL Video Source Compatible ( NTSC : SHR-2040/SHR-2041/SHR2042, SHR-2040N / SHR-2041N / SHR-2042N PAL : SHR-2040P/SHR-2041P/SHR2042P) ■ Able to record the CIF sized (NTSC-352 x 240/PAL-352 x 288) video at the speed of 120 ips(NTSC)/100ips(PAL...
Page 10 - Part Names and Functions
No. Name Function SHR-2040/2041/2042 USER’S MANUAL 3 Part Names and Functions 1-3 Power LED HDD Access LED Displays Normal Access to HDD. Upon Access to HDD, LED repeats on and off. Mode Selection Button Search Audio Setup Button Displays power on/off condition. 1 2 3 5 Network LED Displays both net...
Page 15 - Caution
1-8 No. Name Function Composite Video Signal Input Port (BNC Style Connector) You may use THROUGH port to transmit a video signal to theother video equipment. Audio Signal Input Port (RCA Jack) Audio Signal Output Port (RCA Jack) Composite Video Signal Output Port (BNC Style Connector) VGA Video Sig...
Page 17 - Installation Environment Setup
1 Installation Environment Setup 2-1 Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator.To play DVR on the cabinet or rack, be sure to check the ventilation condition. You should pay attention to the following before you use the product. 1. Do not use it o...
Page 18 - Checking Product & Accessory
2 Checking Product & Accessory 2-2 Upon delivery of a product, you shall unwrap the product and put it on the even floor or whereyou want to use it. Then you shall check if the following items are in it. ■ Main Body ■ User’s Manual ■ One Power Cord ■ Two Brackets- These are not supplied in SHR-2...
Page 19 - HDD Addition
SHR-2040/2041/2042 USER’S MANUAL 3 HDD Addition 2-3 You can add up HDD to the product.(2040-1 HDD/2041-3 HDDs/2042-2 HDDs) However, since the product contains has many parts which may incur electric shock, accident, or product breakdown and improper installation or setup may disturb HDD recognition ...
Page 30 - Connecting the Video, Audio, and Monitor
1 Connecting the Video, Audio, and Monitor 3-1 SHR-2040/2041/2042 USER’S MANUAL [SHR-2040]
Page 32 - Connecting the Network
SHR-2040/2041/2042 USER’S MANUAL 3-3 2 Connecting the Network ● Connecting to Internet through Ethernet(10/100BaseT) ● Connecting to Internet through ADSL [SHR-2040] [SHR-2040]
Page 34 - Connecting the USB
1. There are two USB connecting ports on the front and back of SHR-2040/2041/2042. 2. USB Hard Disk, USB CD/DVD, and USB Memory are connected through the front and back ports of SHR-2040/2041/2042. 3. Only one USB device can be connected with each USB connecting port. 4. If the USB HDD is connected ...
Page 35 - Connecting the Alarm Input/Output
3-6 4 Connecting the Alarm Input/Output The Alarm IN/OUT port in the back of SHR-2040/2041/2042 is composed of the followingelements. ● ALARM IN/OUT Connection Name Function - ALARM IN1 1 - ALARM IN2- ALARM IN3- ALARM IN4 2 - ALARM RESET IN 3 - ALARM OUT1 - ALARM OUT2 ALARM Input Port ALARM Output P...
Page 37 - Connecting the RS-485 Device
3-8 5 Connecting the RS-485 Device ● Connect the RS-485 Device through the back port of SHR- SHR-2040/2041/2042. ● You can install and control the PTZ camera supporting the RS-485 communication. ● You can adopt either Half Duplex or Full Duplex method for the connection. ● Baud Rate supports 600/120...
Page 39 - System Operation
1 System Operation 4-1 SHR-2040/2041/2042 USER’S MANUAL ● Turn the power on and the following LOGO pops up on the screen. ● After the LOGO appears, all of LED in the front flickers 6 times to initialize the system foroperation. ● Upon completion of normal initialization, the Live screen appears acco...
Page 40 - Live screen Mode; Definition of Live Screen Icon
2 Live screen Mode 4-2 Definition of Live Screen Icon The Live screen icons display the current setup and function status of each screen. PTZ N CAM_01 CAM_01 V.Loss : Recording Icon Each icon represents Normal / Event (Alarm + Motion) / Schedule Recording. : Recording Video Size Icon Each icon repre...
Page 41 - Definition of Live Screen Mode
SHR-2040/2041/2042 USER’S MANUAL 4-3 Definition of Live Screen Mode The system receives 3 live images and displays them in the following 3 modes. ● 4 Split Mode: Four channels are split in the screen separately.You are able to choose a channel as you want to in each split mode. ● PIP(Picture In Pict...
Page 42 - Selecting Live Screen Mode
4-4 Selecting Live Screen Mode Each mode may be selected by [MODE Button] and [CH1 ~ CH4 Button]. The following figure shows Live Mode after converted. ● The default setup is 4 Split Screen Mode. ● You are able to choose other modes than Full Screen Mode by the [MODE] button insequence. Whenever you...
Page 43 - Live Channel Selection and Audio On/Off Setup; Audio On/Off Setup in the Full Screen
3 Live Channel Selection and Audio On/Off Setup In other split modes than Full Screen Mode and Auto Sequence Mode, you can choose a channelto be displayed in each split area on your own. In addition, the channel being set to Audio On canbe set to Audio On/Off in all Live Modes. Audio On/Off Setup in...
Page 44 - Freeze and Zoom; Freeze Function
4-6 4 Freeze and Zoom Freeze Function Freeze function pauses the video image in the Live Screen, it is only available in the Live Mode.You can set Freeze On/Off with [FREEZE] Button and [FREEZE LED] is turned on or off depending on the Freeze On/Off setup condition. Zoom Function Zoom function enlar...
Page 45 - Event Monitoring
5 Event Monitoring Event monitoring displays the channel synchronized with a event on the screen when a special event (Sensor/Motion/Video Loss) occurs. Event monitoring On/Off and event duration setup is available in [Menu] ➝ [Monitoring] mode. If you set the event monitoring interval to 5 seconds ...
Page 49 - System
1 System 5-2 ● System Menu has the following items in detail. ● Press the “Enter” key and the ¦ , key to move to Y/M/D. Use the , key to change the date. Press the “Enter” key to come out of the mode. ● TimePress the “Enter” key and the ¦ , key to move to H/M/S. Use the ¦ , key to change t...
Page 51 - Password
5-4 Password ● The Default Password is 4321. ● New PasswordThis is used to change the system password inside SHR-2040/2041/2042. You areallowed to create a password up to 4 digits. Press the “Enter” key and a channelbutton from 1 ~ 4 at the left. Press the “Enter” key after change to move to “NewPas...
Page 53 - Event Log
5-6 ● System Log List Event Log ● It used to check the record regarding Event like Alarm / Motion / Video Loss. ● It displays the contents of a log regarding event and its execution date / time. ● First : Returns to the first Log page. ● Prev : Back to the previous Log page. ● Next : Forwards to the...
Page 54 - System Information and Setup
SHR-2040/2041/2042 USER’S MANUAL 5-7 System Information and Setup ● Software Version : Displays the current version. Setup is not available. ● Broadcast Format : Displays the current Format(NTSC/PAL) . Setup is not available. ● Mac Address : 6 Byte hardware address. Setup is not available. ● Device ...
Page 55 - HDD Setup
5-8 HDD Setup ● HDD Information Displays the number, capacity, and status of ATA and USB device. Setup is not available.Status : Internal HDD, External HDD, Backup HDD ● External HDD Setup 1. Backup/External type You are able to determine the usage of USB.Not Defined ➝ Appears when the usage of conn...
Page 56 - HDD Mode Setup
SHR-2040/2041/2042 USER’S MANUAL 5-9 HDD Mode Setup ● HDD End Mode Stop : Stops recording when HDD is full during the recording.Overwrite : Deletes the original data and save a new data when HDD is full during the recording. ● HDD End Beep On : Beeps when the HDD is full in the recording mode.Off : ...
Page 57 - Remote control Device
5-10 Remote control Device ● MENU for the use of Samsung system keyboard Remote Control Device ID Baudrate Device Samsung System Keybord Parity Date Stop Duplex 03 4800 None 8 1 Half Duplex ● Device A Remote Control Device, being connected to the RS485 port. ● ID This is a private ID of SHR-2040/204...
Page 58 - System Shutdown
SHR-2040/2041/2042 USER’S MANUAL 5-11 System Shutdown ● Terminates the work in action safely and turns the power off. Press “OK” in the confirmationwindow and plug out when you see “Safe to Power Off”. Remote Control Device Caution Caution [System Shutdown]Power-off without terminating the system in...
Page 59 - Camera
5-12 2 Camera ● The detailed Camera Menu items are as follows. ● VideoOn : Camera images from a selected channel appear.Off : Camera images from a selected channel disappear. Covert1 : Displays the information except for the Video information of selected channel. Covert2 : Does not display the any i...
Page 61 - PTZ Device
5-14 PTZ Device ● ID It is an ID for PTZ Camera and available to set from 0 to 255. ● Protocol It is supported by the PTZ device. The following protocols are now being supported. Samsung / Vic. / Pan. / AD / Phi. / Ern. / Pel-D / Pel-P / Vcl. / Dia. / Kal. ● Baurate Baurate is supported by the PTZ d...
Page 62 - Screen Setup
Screen Setup SHR-2040/2041/2042 USER’S MANUAL 5-15 ● It is a window to set Brightness/Contrast/Color for the camera image of each channel. Put the cursor on the channel that you want to adjust and set Brightness/Contrast/Color. Once selected, the channel appears in the right PIP area. Use the or ...
Page 63 - Monitoring
5-16 3 Monitoring ● Event Monitoring It is possible to set to Off/3sec/5sec/10sec/20sec/30sec/Continuous. ① Off : Event Monitoring does not operate to turn to the screen where an event occurs. ➁ 3sec / 5sec / 10sec / 20sec / 30sec : Sets the duration time of screen in the Auto Sequence mode. ➂ Conti...
Page 65 - Recording Mode; Record Mode
5-18 4 Recording Mode Record Mode ● Details for Record Mode Menu are as follows. If you press the front “REC” button, the mode value to be recorded will be set. ☛ For the setup of Event Recording Mode value, refer to 5-20. Event RecordingMode Setup Menu. ● Mode On : The current channel is recorded i...
Page 66 - Record Video size Mode
SHR-2040/2041/2042 USER’S MANUAL 5-19 ● Video size It sets the video to be recorded. Half D1 : (NTSC) 720x240(N) ➝ Normal (PAL) 720x288(N) ➝ Normal CIF : (NTSC) 352x240(C) ➝ CIF (PAL) 352x288(C) ➝ CIF ● Auto Deletion Press the [Off] button at the bottom of left to select either OFF or On. Select “On...
Page 67 - Event Record Mode
5-20 5 Event Record Mode ● The detailed items of Event Record Menu are as follows. Event Record Mode setup ● Event Record Mode setup Sets a mode to be recorded when an event occurs. ● V. Size (Video Size ) Sets the size of a screen to be recorded.Half D1 : (NTSC) 720x240(N) ➝ Normal (PAL) 720x288(N)...
Page 69 - Alarm Detection Setup
5-22 Alarm Detection Setup ● Off : Sensor does not operate. ① N.O(Normal Open) Sensor : Sensor remains open all the time and if closed, an alarm will be issued. (A Contact) ➁ N.C(Normal Close) Sensor : Sensor remains closed all the time and if open, an alarm will be issued. (B Contact) ● Cam Sets a ...
Page 70 - Motion Detection Setup
SHR-2040/2041/2042 USER’S MANUAL 5-23 Motion Detection Setup ● Motion Detection Mode Off : Motion Detection does not operate On : Motion Detection operates. ● Area Selects the Motion Detection area. It is composed of 45x40(NTSC)/45x48(PAL) sized Block. It is impossible to set 4 block rows(Up/Down/Le...
Page 71 - Video Loss Detection Setup
5-24 ● Sensitivity Sets the sensitivity of motion detection. Sensitivity grade consists of Low ➝ Medium ➝ Very High in the ascending order. ● Alarm-Out Sets the Alarm-Out when Motion occurs. 5 Alarm Outs are supported. Select an alarm-out that you want to synchronize with the current motion channel....
Page 72 - Record Schedule
SHR-2040/2041/2042 USER’S MANUAL 5-25 6 Record Schedule This setup selects a time to record automatically.Selection by the day or by the time is available.The default value is set to “Event Record”. ● Press “CH >” copies the value of Channel 1 to all the channels. ● The horizontal axis numbered f...
Page 74 - Backup
SHR-2040/2041/2042 USER’S MANUAL 5-27 7 Backup ● If there is a device, the free space and the backup device is displayed. ● Select a date, time, and camera No. to backup, and press “Start”. ● When you change Start Date/Time or End Date/Time, free space keeps updated inthe Free Space zone. ● A file n...
Page 75 - Network; IP Setup
5-28 8 Network ● Connection Mode Designates the kind of the network connected to the main body of SHR-2040/2041/2042.Static IP : When the main body is connected to the network with Static IP. Dynamic IP : When the main body is connected to the network with Dynamic IP supplied by DHCP. ADSL(PPPoE) : ...
Page 77 - Transfer Protocol Settings
5-30 Note Note If you want to connect IP Router with the main body of SHR-2040/2041/2042, you shall designate a port for SHR-2040/2041/2042 in the IP Router setup menu.The main body of SHR-2040/2041/2042 uses 4 ports for TCP communication.In addition, if you want to use the DHCP function backed by I...
Page 78 - Callback Settings
SHR-2040/2041/2042 USER’S MANUAL 5-31 Callback Settings ● The Callback function is used to forward a callback message to the IP where SmartVieweris in action in case Alarm, Motion Detection, or Video Loss event occurs. ● On/Off : Off is default but you may choose On. ● IP Address : IP setting is ava...
Page 79 - Network Setup; Port Setup for SmartViewer Connection; In the event of TCP Setup from Transfer Protocol Setup Page
5-32 9 Network Setup Port Setup for SmartViewer Connection ● The Port value for DVR registration of SmartViewer (Setup ➝ Site Setup) shall be as same as that of the set (TCP). ● If you want to use the IP Router, you shall forward the activated Port depending on thecurrent setting value. - If set to ...
Page 81 - PTZ Camera Control Mode
1 PTZ Camera Control Mode 6-1 ● Select a proper PTZ camera Configuration value in MENU to enter PTZ Control Mode. ● Selected in MENU, the PTZ symbol( ) is displayed on the channel in the screen. ● If you press the Enter( ) button among direction keys in front of Split Screen, a bluebar will appear i...
Page 84 - Preset Setup
3 Preset Setup 6-4 ● Records a certain position of PTZ Camera. ● Memorizes up to 20 PTZ Camera positions at the moment. ● Press the Preset button in front of SHR-2040/2041/2042 in Single Screen PTZ CameraControl Mode to set up Preset. ● After Preset setup, press ENTER. PTZ TELE WIDE VIEW PRESET Note...
Page 86 - Camera Menu Setup
4 Camera Menu Setup 6-6 ● Camera Menu is a menu supplied by PTZ Camera itself. This Menu sets up several conditions of PTZ Camera. ● Press the Preset button in front of SHR-2040/2041/2042 in Single Screen PTZ CameraControl Mode to select Camera Menu. ● Press the “Preset” button in front of SHR-2040/...
Page 87 - Preset View
SHR-2040/2041/2042 USER’S MANUAL 5 Preset View 6-7 ● Preset setup allows your movement to a certain saved position of PTZ Camera. ● Press the VIEW button in front of SHR-2040/2041/2042 in Single ScreenPTZ Camera Control Mode to select Preset.(For example, Samsung Protocol) ● Control the cursor until...
Page 88 - Other View
6 Other View 6-8 ● Press the “VIEW” button in front of SHR-2040/2041/2042 in Single Screen PTZ CameraControl Mode to supply PTZ Camera. This is a very special function. ● After you select a function, press Enter. Then the function will be checked and start running. ● If you select other function dur...
Page 91 - Schedule Recording
2 Schedule Recording 7-2 ● While “Record Schedule” or “Schedule/Event recording” is selected in the Record Schedulemenu, Schedule Recording automatically starts. Otherwise, Schedule Recording remainsinactivated. During the Schedule Recording, Recording Icon appears on the screen. During the recordin...
Page 92 - Event Recording; arning
SHR-2040/2041/2042 USER’S MANUAL 3 Event Recording 7-3 ● Alarm Detection Sensor operation mode in Alarm of Event Record menu shall be set to N.O (Normal Open)or N.C (Normal Close). ● Motion Detection Motion detection in the Event Recording menu shall be set to On. ● Video Loss Detection Video Loss i...
Page 95 - Calendar Search
1 Calendar Search 8-2 ● Be sure to select both the channel and the date to search. And press the [Start] button tosearch for the desired time. ● Use a calendar to search the video file of desired time. Four channels in maximum are inthe range of search. ● Select the channel up to 4 by the use of ¦ ,...
Page 96 - Event Search
SHR-2040/2041/2042 USER’S MANUAL 8-3 ● Searches Normal Recording, Schedule Recording, Alarm Recording, Motion Recording, andV.Loss(Video Loss) Recording by the time. ● You shall select a channel to search to see the event information of the channel. ● On the basis of event information for each chann...
Page 98 - Go to First Search
SHR-2040/2041/2042 USER’S MANUAL 8-5 ● Searches the oldest one among recorded video files. Up to 4 channels can be searched atonce. ● After you select a channel with the , , [Enter] button, the checkbox on the right of the selected channel number will be checked. ● Press the [Start] button want ...
Page 99 - Go to Last Search
5 Go to Last Search 8-6 ● Searches the latest one among recorded video files. Up to 4 channels can be searched atonce. ● After you select a channel with the , ,[Enter] button, the checkbox on the right of the selected channel number will be checked. ● Press the [Start] button want to start the s...
Page 101 - Playback
7 Playback 8-8 Note Note Pressing the PLAY button( ) does not affect the playback as far as the user stays in theMENU. Be sure to exit from the MENU to start the playback. ● Press the STOP button( ) to stop the playback. If you press the Playback/PAUSE button( ) once more, the recording will resume ...
Page 106 - Feature
2 Feature 9-2 ● Thanks to the transmission of video data compressed by the MPEG-4 VideoCompression method, it can play the video images of good quality. ● Thanks to the G.726 Voice Compression method, it supplies the voice data ofgood quality. Use of armored MIC improves the quality of remote voice....
Page 108 - Smart Viewer Installation
4 Smart Viewer Installation 9-4 Smart Viewer Installation ● Put a Smart Viewer Program CD in CD-ROM and open the “Smart Viewer” folder in the CD. ● Run the “Setup.exe” file.
Page 111 - Smart Viewer Program Execution
SHR-2040/2041/2042 USER’S MANUAL 5 Smart Viewer Program Execution 9-7 ● Double-click the Smart Viewer icon in the background screen to run the program.
Page 112 - Smart Viewer Initial Screen
6 Smart Viewer Initial Screen 9-8 ● Screen Description ! This is the button to enter the Search mode in which you can search and play remote the video file recorded in SHR-2040/2041/2042 and enter the Monitoring mode for real-time video monitoring. @ This button terminates or minimizes the program. ...
Page 113 - Monitoring Mode; Connection Failure Cases
SHR-2040/2041/2042 USER’S MANUAL 7 Monitoring Mode 9-9 ● DVR(SHR-2040/2041/2042) / SITE Connection- Select the name of DVR(SHR-2040/2041/2042) or site for connection and click the connection button. Connection Failure Cases 1. Password Certification Failure - In case of discord between the Network p...
Page 127 - Search Mode
SHR-2040/2041/2042 USER’S MANUAL 8 Search Mode 9-23 ● The initial screen of search mode - The search mode is divided into the remote mode to search and play the SHR-2040/2041/2042 video and the local mode to play .dvr file saved in thedirectory designated by your PC. ! To change to the search mode f...
Page 134 - Setup Mode
9 Setup Mode 9-30 ● Initial Screen ! Button to select items for DVR Setup, Viewer Setup, Site Setup, and S/W Version setup. @ It shows what the selected Setup item can set up in detail. # button to terminate the setup window. $ Button to save the information revised in the setup window, remark the i...
Page 136 - DVR Setup
9-32 DVR Setup - Click the [DVR Setup] button for DVR Setup.- You can change remotely the setup items of SHR-2040/2041/2042 Menu, being connected with Smart Viewer. - DVR Setup is composed of 5 items; System, Camera/Audio, Monitoring, Recording, and Network. Note Note - - Y Y ou are authorized with ...
Page 149 - Viewer Setup
SHR-2040/2041/2042 USER’S MANUAL 9-45 Note Note - SHR-2040/2041/2042 uses 4 ports for TCP connection.- The PORT number is flexible and 4 consecutive numbers are grouped for the change ( 554,555,556,557 ➝ 558,559,560,561 ) - If you use the IP Router for network composition, you should allocate a prot...
Page 152 - Site Setup
9-48 Site Setup - Click the [Site Setup] button for Site Setup. - The information of DVR(SHR-2040/2041/2042) or Site that you want to connect by Smart Viewer is set in the Site Setup. - Smart Viewer allows you to connect with DVR(SHR-2040/2041/2042) or Site registered only here. 1 3 5 2 4 ! The DVR(...
Page 164 - Appendix
Page 165 - Product Specification
1 Product Specification 10-1 SHR-4160N/P USER’S MANUAL Item Details Remarks CPU 32bit RISC CPU Memory SDRAM : 128MByte Flash : 16 MByte OS Embedded OS Broadcasting NTSC System Input Voltage 2040-DC 12V, AC 110-220(NTSC), AC 110-230(PAL) 2041/2042 - AC 110-220(NTSC) AC 100-230(PAL) Power Consumption ...
Page 168 - The specification of HDD and peripheral device
2 The specification of HDD and peripheral device 10-4 ● Internal ATA HDD/IEEE1394/USB HDD I/F External HDD Maker RPM Capactity Interface Buffer Series Name Model No Remark 120 GB160 GB120 GB Maxtor 160 GB250 GB Western 120 GB Digital 160 GB CD-R CD-RW CD-R CD-RWDVD+R DVD-R DVD+RW ❉ DVD-RW is not sup...
Page 169 - Outline Drawings
SHR-2040/2041/2042 USER’S MANUAL 3 Outline Drawings 10-5 [SHR-2040] [SHR-2041]
Page 171 - Factory Default
SHR-2040/2041/2042 USER’S MANUAL 10-7 4 Factory Default This restores the Network information and preset values in SHR-2040/2041/2042 to the original state at the time of factory shipment. Factory Default will be done as follows; - Use System / Load Factory Default in MENU or, - If you hold on to th...
Page 173 - Frame Specification for the Playback
SHR-2040/2041/2042 USER’S MANUAL 10-9 5 SHR-2040/2041/2042 Smart Viewer Frame Specification for the Playback FRAME Viewer Screen VIDEO SIZE RATE Split Mode Half D1(N) CIF (C) Nine-split 1 frame/sec 15 frame/sec Fore-split 15 frame/sec 15 frame/sec Single 15 frame/sec 15 frame/sec Half D1(N) CIF (C) ...
