Samsung SCC-130BP - User Manual

Page 2 - iii; ii; CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

1. Read all of these instructions. 2. Save these instruction for later use. 3. Unplug this appliance system from the wall outlet before cleaningDo not use liquid cleaners or aerosol cleaner.Use a damp cloth for cleaning. 4. Do not use attachments not recommended by the appliance manufacturer, as the...

Page 3 - iv

13. Unplug this appliance from the wall outlet and refer servicing to qualified servicepersonnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the appliance. c. If the appliance does not operate normally by following the opera...

Page 4 - Contents; COLOR ROLLING

Contents 1. Introduction ........................................................ 3 2. Features .............................................................. 4 3. Installation .......................................................... 5 Precautions in Installation and Use .................... 5 Con...

Page 5 - Precautions in Installation and Use; High Sensitivity

3. Installation Precautions in Installation and Use ① Do not attempt to disassemble the camera yourself. ② Be cautious in handling the camera. Avoid striking orshaking the camera. Be cautious to avoid damage onthe camera caused by improper storage or operation. ③ Do not expose this camera to rain or...

Page 6 - Mounting the Lens; Connecting Auto Iris Lens Connector; Pin Number DC Control Type

7 User Guide E Mounting the Lens Loosen a screw fixing the Flange Back Adjustment Ring byturning it counterclockwise and turn the Adjustment Ring tothe "C" direction (counterclockwise) until it stops. Failure todo so may result in a damage caused by the bump of the lensagainst the image sens...

Page 7 - Adjusting Back Focus; Setting Lens Selection Switch

9 User Guide E Adjusting Back Focus Although the Back Focus of the camera has been adjustedin the factory before its shipment, the focus may not beaccurate for a certain type of the lens. In this case, followthe procedures below to adjust the Back Focus. First,following is how to adjust the Back Foc...

Page 8 - Connecting Cable

11 User Guide E Connecting Cable After mounting the lens and setting the Lens SelectionSwitch, connect the prepared cable to each terminal of thecamera. ① First, connect one end of the BNC cable to the VideoOutput Terminal (VIDEO OUT) of the camera. ② Then connect the other end of the BNC cable to t...

Page 10 - Names and Functions of Parts; • Side View; Groove for Mount Adapter; Note

15 User Guide E ③ Auto Iris Lens Connector Used for supplying power, which is required to controlthe iris of the lens, as well as control signal, videosignal, or DC signal to the Auto Iris Control Lens. ④ Auto Iris Lens Control Cable Used for transmitting the control signals to the camerato control ...

Page 11 - AC24V/DC12V Power Input Camera; • Rear Panel; AC230V Power Input Camera

① Power Connection Terminal Terminal to be connected to the power (adapter) cableConnect it to AC 24V or DC 12V. ② Power Indication LED While the power is properly supplied to the camera, theLED is turned on. ③ , ④ INC/DEC Switch The LINELOCK mode is useful for controlling VerticalSynchronous Phase....

Page 12 - Function Switches

19 User Guide E 3) SW3 (FL): This is to prevent flicker on the screen when NTSCsystem is used in 50HZ power supply region and PALsystem is used in 60HZ power supply region. That is toprevent shaking on the screen resulted from thediscordance of the vertical sync frequency and theflicker frequency of...

Page 13 - Product Specifications; Item; DC Iris Level Control

21 User Guide E 5. Product Specifications SCC-130B/131B Item Contents Product Type CCTV Camera Broadcasting NTSC STANDARD SYSTEM System CCD 1/3” IT type S-HAD CCD No. of Pixel 130B : 510(H) x 492(V) 131B : 768(H) x 494(V) Scanning Type 525 Line, 2:1 Interlace Frequency INTERNAL : 15,734 H Z (H) 59,9...