Page 3 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE; Reorient or relocate the receiving antenna.
C1492M-I (8/05) 3 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...
Page 4 - Important Notice; Should any problems occur, Pelco will provide on-site
4 C1492M-I (8/05) Important Notice All companies make changes and improvements in their products on a regular basis. Because this product is interfacing with equipment not manufactured by Pelco, the possibility exists that the interface protocols have changed or are in a different confi guration fro...
Page 5 - Description; systems. Once installed the Spectra dome, ExSite, or Esprit system
C1492M-I (8/05) 5 Description The TXB-AD translator board allows American Dynamics controllers to communicate with Pelco’s Esprit ® , ExSite ™ , and Spectra ® systems. Once installed the Spectra dome, ExSite, or Esprit system receives Manchester code commands from the American Dynamics controller an...
Page 6 - Esprit Integrated Positioning System Installation; The following items are supplied:; TXB-AD TRANSLATOR BOARD INSTALLATION AND SETTINGS; Remove the left cover on the pan and tilt.
6 C1492M-I (8/05) Esprit Integrated Positioning System Installation The following items are supplied: 1 TXB-AD translator board (printed circuit board) 1 4-40 screw with lock washer (for Spectra II ® Series only) 1 6-32 screw with lock washer (for Spectra III ™ Series only) TXB-AD TRANSLATOR BOARD I...
Page 8 - ESPRIT SYSTEM SETTINGS AND CONNECTIONS; For American Dynamics controllers with only 32 presets:; Set SW1-5 to the ON
8 C1492M-I (8/05) 4. Install the TXB-AD translator by inserting the 16-pin connector located on the back of the TXB-AD board into the mating connector on the Esprit system’s board. Refer to Figure 1 and Figure 2. 5. Reinstall the nut and washer on the standoff to secure the translator board. ESPRIT ...
Page 9 - From AD Controller
C1492M-I (8/05) 9 Figure 5. How to Install Cover 4. Remove the pan and tilt from the base of the Esprit System. Check the control wiring inside the base of the unit. NOTE: To wire the connector for the controller, refer to the manual supplied with the American Dynamics controller. 5. Reinstall the p...
Page 10 - Spectra Dome Installation; TXB-AD Translator Board Layout, Front and Back
10 C1492M-I (8/05) Spectra Dome Installation The following items are supplied: 1 TXB-AD translator board (printed circuit board) 1 4-40 screw with lock washer (for Spectra II Series only) 1 6-32 screw with lock washer (for Spectra III Series only) TXB-AD TRANSLATOR BOARD INSTALLATION AND SETTINGS 1....
Page 11 - Receiver Location
C1492M-I (8/05) 11 Figure 7. Receiver Location 3. Set DIP switches on the TXB-AD. Refer to Figure 6 and Table A. 4. Install the TXB-AD board. Refer to Figure 8 and Figure 9 and do the following: a. Open the hinged door to the back box. Push the tab lock towards the wall of the unit and lift the door...
Page 13 - SPECTRA SYSTEM SETTINGS AND CONNECTIONS; Appendix; Dome Drive
C1492M-I (8/05) 13 SPECTRA SYSTEM SETTINGS AND CONNECTIONS 1. Check the wiring to the controller. NOTE: To wire the connector for the controller, refer to the manual supplied with the American Dynamics controller. 2. Close the interconnect door. 3. Verify that all SW1 (Spectra II) or SW3 (Spectra II...
Page 14 - ExSite Explosionproof System Installation; Turn off the power to the ExSite system.
14 C1492M-I (8/05) ExSite Explosionproof System Installation The following items are supplied: 1 TXB-AD translator board 1 4-40 screw with lock washer (for Spectra II Series only) 1 6-32 screw with lock washer (for Spectra III Series only) TXB-AD TRANSLATOR BOARD INSTALLATION AND SETTINGS 1. Turn of...
Page 17 - EXSITE EXPLOSIONPROOF SYSTEM SETTINGS; Set SW3-1 to the ON
C1492M-I (8/05) 17 EXSITE EXPLOSIONPROOF SYSTEM SETTINGS 1. Check wiring to controller. 2. Verify that all SW3 switches on the ExSite system are set to the OFF position. For American Dynamics controllers with only 32 presets: Set SW3-1 to the ON position. Refer to Figure 13 for switch location. 3. S...
Page 18 - Operation; AD Keyboard Function
18 C1492M-I (8/05) Operation Activate preset 70 to access the camera menus. See below for information on how the translator performs. This shows how the AD keyboard relates to the Pelco translator. AD Keyboard Function Unit Action Pelco Function Spectra III/ExSite Special Function Pan, tilt, zoom, f...
Page 21 - Troubleshooting; Symptom; – Are the pins on the translator
C1492M-I (8/05) 21 Troubleshooting Symptom Ensure Check/Perform Unit does not respond properly to controller. Make sure your controller is trying to communicate with the unit and not another camera. – Are the pins on the translator board inserted properly into the mother board? (If not, damage to th...
Page 22 - TXB-AD DIP Switch Settings; Switch
22 C1492M-I (8/05) Appendix Table A. TXB-AD DIP Switch Settings Switch Position Result 1 OFF ON Spectra III/ExSite setting Spectra II/Esprit setting 2 OFF ON Speeds will match AD Ultra Dome Speeds will match older (before revision 2.00) TXB-AD versions 3 OFF ON Turbo mode enabled on power-up Turbo m...
Page 23 - American Dynamics Camera Assignments
C1492M-I (8/05) 23 Table B. American Dynamics Camera Assignments Group 1 Group 2 Group 3 Group 4 Group 5 Group 6 Group 7 Group 8 Address 1 65 129 193 257 321 385 449 1 2 66 130 194 258 322 386 450 2 3 67 131 195 259 323 387 451 3 4 68 132 196 260 324 388 452 4 5 69 133 197 261 325 389 453 5 6 70 134...
Page 31 - PRODUCT WARRANTY AND RETURN INFORMATION
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic...