Page 2 - CONTENTS; Section; PROGRAMMING GUIDE - SPECTRA II LOWLIGHT COLOR,
2 Pelco Manual C2419M-A (5/00) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 3 OPERATION ...................................................................................................................... 4 POWER-UP DISPLA...
Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; Only use replacement parts recommended by Pelco.; MEASURES DE SECURITE IMPORTANTES
Pelco Manual C2419M-A (5/00) 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel andconform to all local codes. 2. Unless the unit is specificall...
Page 4 - OPERATION; Protocol C
4 Pelco Manual C2419M-A (5/00) OPERATION POWER-UP DISPLAY When the Spectra II™ dome is powered up, the selected protocol, revision number, andother information is displayed on the monitor. For example, the screen might show thefollowing information: The information displayed depends on the selectedp...
Page 6 - The Spectra II
6 Pelco Manual C2419M-A (5/00) PATTERNS The Spectra II dome can do either one full pattern (1.5, 3, or 6 minutes long) or two halfpatterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tiltor lens command. Presets, flip, and turbo are not allowed in a pattern. Zone ...
Page 7 - Park; AUTO IRIS; Hold down the Iris Open button until the iris is wide open.
Pelco Manual C2419M-A (5/00) 7 AUXILIARY OUTPUTS An AUX 1 command from the controller will activate the relay in the dome and operate thedevice that is connected to the relay. The relay will remain latched until a clear command isissued. An AUX 2 command from the controller will place a ground at th...
Page 8 - PROGRAMMING; Programming Guide - Spectra II LowLight Color; For detailed instructions, refer to the following sections.; MAIN MENU
8 Pelco Manual C2419M-A (5/00) PROGRAMMING Programming Guide - Spectra II LowLight Color Spectra II Monochrome 1. Access main menu (preset 95). 2. Make main menu selections.Joystick: Move up or down to position cursor orto toggle between selections. Iris Open: EnterIris Close: Cancel PRESETS The fol...
Page 10 - Pattern length is set; ALARM PATTERN
10 Pelco Manual C2419M-A (5/00) ALARMS The Spectra II dome has seven alarm inputs, which can be designated as either high or lowpriority. The high priority setting is significant when more than one alarm is activated. If priority inalarms is not required, leave all alarms in the low setting. Refer t...
Page 11 - ALARM RESUME
Pelco Manual C2419M-A (5/00) 11 6. Position the cursor (>) beside the number of the alarm input for which you want to setthe pattern. 7. Press the Iris Open button. The cursor moves to the right, beside the words Full Pat,Half Pat 1, Half Pat 2, or No Pattern. 8. Move the joystick up or down to t...
Page 13 - The following are the settings for auto iris:
Pelco Manual C2419M-A (5/00) 13 AUTO IRIS The following are the settings for auto iris: ModeLevelPeak To change the settings for auto iris:1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Positio...
Page 15 - AGC MODE; GAIN; Press the Iris Open button to enter the Camera menu.
Pelco Manual C2419M-A (5/00) 15 Main Menu <Camera><Line Sync><Power Up><Aux><Alarms, Zone Blank><Other>EXIT Camera Menu Backlight comp Off Zoom limit x- - Reset camera<Gain/AGC><Auto-iris><Next>Exit Gain/AGC Menu AGC mode Auto Gain 0 Exit Gain - ...
Page 16 - Programming
16 Pelco Manual C2419M-A (5/00) LIMIT STOPS Main Menu <Camera><Line Sync><Power Up><Aux><Alarms, Zone Blank><Other>EXIT Other Menu Auto flip On Proportional pan On Limit stops On Park time minutes 0 Scan speed deg/s 25 Pattern length 6 min Exit There are two types...
Page 17 - LINE SYNCHRONIZATION
Pelco Manual C2419M-A (5/00) 17 LINE SYNCHRONIZATION Main Menu <Camera><Line Sync><Power Up><Aux><Alarms, Zone Blank><Other>EXIT Line Sync Menu Line sync On Line sync phase 0 Exit If cameras are out of phase with each other, they may produce what appears to be ver...
Page 18 - PARK TIME MINUTES; Preset 1 must be
18 Pelco Manual C2419M-A (5/00) PARK TIME MINUTES This feature causes the dome to park at preset 1 after a programmed number of minutes ofcontrol inactivity. The time can be set from 1 minute to 720 minutes (12 hours), or it can be setto zero, which disables this feature. To change the park time:1. ...
Page 19 - The default setting is Default.; PATTERN LENGTH; If the; The Spectra II dome can do the following:
Pelco Manual C2419M-A (5/00) 19 This feature lets the dome resume a desired condition following power-up. The menuincludes the following choices. Default - On power-up, the dome goes through a configuration cycle and stops atzero reference, showing “Configuration Done,” address, and modesettings on ...
Page 20 - PROPORTIONAL PAN
20 Pelco Manual C2419M-A (5/00) Main Menu <Camera><Line Sync><Power Up><Aux><Alarms, Zone Blank><Other>EXIT Other Menu Auto flip On Proportional pan On Limit stops On Park time minutes 0 Scan speed deg/s 25 Pattern length 6 min Exit There are two proportional pan ...
Page 21 - RESET CAMERA
Pelco Manual C2419M-A (5/00) 21 RESET CAMERA Main Menu <Camera><Line Sync><Power Up><Aux><Alarms, Zone Blank><Other>EXIT Camera Menu Backlight comp Off Zoom limit x- - Reset camera<Gain/AGC><Auto-iris><Next>Exit Resetting the camera returns the s...
Page 22 - SCAN SPEED; SHARPNESS; AUTO SHARPNESS; - The cursor moves to a numeric value. Move the joystick up or down
22 Pelco Manual C2419M-A (5/00) SCAN SPEED Next Menu LowLight limit 2 Shutter speed Auto Auto focus mode Auto <Sharpness><White balance>Prev (back to prev. menu)Exit Main Menu <Camera><Line Sync><Power Up><Aux><Alarms, Zone Blank><Other>EXIT Main Menu ...
Page 23 - SHUTTER SPEED; There are several electronic shutter speed settings:; Spectra II; Auto
Pelco Manual C2419M-A (5/00) 23 SHUTTER SPEED Next Menu LowLight limit 2 Shutter speed Auto Auto focus mode Auto<Sharpness><White balance>Prev (back to prev. menu)Exit Main Menu <Camera><Line Sync><Power Up><Aux><Alarms, Zone Blank><Other>EXIT Camera M...
Page 24 - ZONES
24 Pelco Manual C2419M-A (5/00) WHITE BALANCE (Color Camera Only) Next Menu LowLight limit 2 Shutter speed Auto Auto focus mode Auto <Sharpness><White balance>Prev (back to prev. menu)Exit Main Menu <Camera><Line Sync><Power Up><Aux><Alarms, Zone Blank><O...
Page 25 - ZOOM LIMIT; Press the Iris Open button to enter the Alarms, Zone Blank menu.; ZONE BLANK
Pelco Manual C2419M-A (5/00) 25 NOTE: The Spectra II LowLight Color cameracannot do electronic zoomin a pattern. Optical zoomwill operate in a pattern. Main Menu <Camera><Line Sync><Power Up><Aux><Alarms, Zone Blank><Other>EXIT Camera Menu Backlight comp Off Zoom ...
Page 26 - MAINTENANCE; DOME CLEANING; SERVICE MANUAL; SPECIFICATIONS; MECHANICAL; CAMERAS
26 Pelco Manual C2419M-A (5/00) MAINTENANCE DOME CLEANING Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch thesurfaces of the dome. Exterior Surface - Clean the dome’s exterior surface with a nonabrasive cleaning cloth andcleaning agent that is safe for acry...
Page 28 - REVISION HISTORY; PRODUCT WARRANTY AND RETURN INFORMATION
28 Pelco Manual C2419M-A (5/00) Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. © Copyright 2000, Pelco. Endura and ExSite are trademarks of Pelco. All rights reserved. U.S. Patent No. 5,931,432. REVISION HISTORY Manual # Date Comments C2419M...
