Pelco PMCL-WMT - Manual
Pelco PMCL-WMT – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Concrete must be a minimum of 3600 psi or 25 Mpa density.
- Page 3 – REVISION HISTORY; Date; Inserted statement per UL about minimum 2 x 4 wood stud.
- Page 4 – PRODUCT WARRANTY AND RETURN INFORMATION; WARRANTY
C2224M-B (12/06)
PMCL-WMT
Monitor Mount
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Installation should be done only by qualified personnel and conform to all local codes.
6. Only use installation methods and materials capable of supporting four times the maximum specified load.
7. Only use replacement parts recommended by Pelco.
8. This unit is designed for indoor use only, and it must not be installed where exposed to rain or moisture.
Description
The PMCL-WMT is a tilt/swivel wall mount that can be used to mount any of Pelco’s 200, 300, or 400 Series flat panel LCD monitors. This mount can also
support most sizes of Pelco’s 500 Series LCD monitors, although a PMCL-V200 adapter plate may be required. This mount can be swiveled 360 degrees to
allow you to use the monitor in either landscape or portrait view. The mount also allows you to tilt the monitor 35 degrees for the best viewing angle.
The PMCL-WMT is capable of supporting a maximum load of 90 pounds (40.8 kg).
Installation
The following parts are supplied:
Qty
Description
1
Wall bracket
1
Monitor mount
4
M4 x 10 mm pan head Phillips screws, stainless steel
4
Split lock washers
4
M6 x 12 mm pan head Phillips screws, stainless steel
4
Flat washers
1
10-32 socket head screw
1
Flat washer, #10, stainless steel
1
Allen wrench, 3/16"
1
Allen wrench, 5/32"
To install the tilt/swivel wall mount:
1. Disassemble the monitor mount from the wall bracket by removing the 10-32 socket head
screw and flat washer from the underside of the mount. Use the 5/32-inch Allen wrench
(supplied) to loosen the screw. Slide the two pieces apart and retain the washer and
screw for reassembly.
2. Attach the monitor mount to the monitor. Refer to Figure 1 and do one of the following:
•
31-inch Monitor or Smaller:
Align the monitor to the correct hole
pattern on the mounting plate. Use the M4 x 10 mm screws and split
lock washers (supplied) to secure the monitor to the mounting plate.
or
•
Monitors Larger than 31-inches:
Align the monitor to the outside
hole pattern of the monitor plate. Use the M6 x 12 mm screws and
flat washers (supplied) to secure the monitor to the mounting plate.
Figure 1.
Attaching the Monitor Mount
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
3. Attach the wall bracket to the wall with the short side pointing down. Mounting hardware is not supplied. a. If installing the mount to a wood stud wall, the stud must be at least 2 inches x 4 inches with a maximum 0.5-inch thick layer of wallboard or plywood. Use the following steps to attach th...
4. Carefully slide the monitor mount into the slots of the wall bracket. Use the 10-32 socket head screw and the flat washer (supplied) to fasten the wall bracket to the monitor mount. Refer to Figure 4. Use the 5/32-inch Allen wrench (supplied) to tighten the screw. Figure 4. Attaching the Wall Mou...
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherlands |...
