Pelco PDF8 Series - Manual
Pelco PDF8 Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Figure 2. Camera and Lens Installation; Figure 3. Acrylic Viewing Dome Installation; Extend the lens to the maximum length.; Lower Dome Installation; Turn the dome so that the viewing slot is in front of the camera lens.
- Page 3 – Wire Gauge; Maximum distance from transformer to load; Table B. 24 VAC Wiring Distances; Total; An enclosure; Wire gauges are; Table A. Video Coaxial Cable Requirements; Maximum Distance
- Page 4 – WARRANTY AND RETURN INFORMATION; REVISION HISTORY; Date; MAINTENANCE
C1463M-A (12/00)
PDF8 Series
Pendant Fixed Mount Dome
®
3500 Pelco Way
Clovis, CA 93612-5699
USA
In North America & Canada:
Tel (800) 289-9100
FAX (800) 289-9150
DataFAX (800) 289-9108
International Customers:
Tel +1(559) 292-1981
FAX +1(559) 348-1120
DataFAX +1(559) 292-0435
PelcoEurope BV
Dillenburg Center
Dillenburgstraat 5F
5652 AM Eindhoven
The Netherlands
Tel +31(40) 251-9870
FAX +31(40) 251-9835
Pelco Online
www.pelco.com
NOTE:
The length of pipe used
may cause noticeable motion on
the video display. If this occurs,
the pipe will require additional
support by bracing, guy wires, etc.
CAUTION:
The mount
area must be capable of
supporting up to 40
pounds (18.12 kg) of weight.
Figure 1. Back Box Cap and Back Box
Installation
MOUNT
PIPE
(NOT SUPPLIED)
BACK BOX
CAP
BACK BOX
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1.
Installation and servicing should only be done by qualified service personnel and conform
to all local codes.
2.
Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclosure,
it is designed for indoor use only and it must not be installed where exposed to rain and
moisture.
3.
Only use replacement parts recommended by Pelco.
4.
The installation method and materials should be capable of supporting four times the
weight of the enclosure, pan/tilt, camera and lens combination.
Please thoroughly familiarize yourself with the information in this manual prior to installation and
operation.
DESCRIPTION
PDF8 Series domes are pendant style units designed for indoor use only. The dome can be
mounted to a ceiling or wall using a suitable length pipe (threaded at both ends) and a mount/
adapter. All PDF8 Series pendant domes are compatible with Pelco IWM Series Wall Mount, the
MRWA Wall Mount, and the MRCA Ceiling Mount.
Models
PDF8-0
Pendant dome with opaque black bubble and smoked viewing slot (1/2 f-stop
of light loss)
PDF8-1
Same as the PDF8-0 except bubble is opaque black with a clear viewing slot
INSTALLATION
Mount, Back Box Cap and Back Box Installation
1
Refer to the instructions supplied with
the IWM, MRWA, or MRCA to install the
mount for the PDF8 Series dome. Bring
the wiring for the dome through the
mount. Refer to Tables A and B for wir-
ing distances.
2
Install a threaded pipe with a minimum
length of 2.50-inches into the mount.
Tighten the pipe to the mount with torque
of approximately 30 ft-lb.
3
Refer to Figure 1 and install the back
box cap and back box. Pull wiring from
the mount through the back box cap and
into the back box. Slide the back box
cap over the pipe and screw the back
box onto the threaded pipe. Tighten the
back box by lightly applying torque, ap-
proximately 20 ft-lb.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Figure 2. Camera and Lens Installation TILT TABLEASSEMBLY ADJUSTMENTBOLT TILT TABLE VIEWING DOME TILT TABLE RETAINING CLIP POSITIONINGRIVETS HOLE PIN BEZEL Figure 3. Acrylic Viewing Dome Installation Figure 4. Lower Dome and Bezel Installation Camera and Lens Installation 1 Refer to Figure 2 and att...
Wire Gauge Maximum distance from transformer to load Table B. 24 VAC Wiring Distances The following are the recommended maximum distances for 24 VAC applications and arecalculated with a 10-percent voltage drop. (Ten percent is generally the maximum allowablevoltage drop for AC-powered devices.) Tot...
WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanship for a period of one year after the date of shipment. Excep-tions to this warranty are as noted below: • Three years on Genex ® Series (multiplexers, server, and keyboard). • Two years on...
