Pelco MS504BAFL - Manual - manualsarea.com

Page 2 - CONTENTS; LIST OF TABLES

2 Pelco Manual C820M-D (1/01) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 3 DESCRIPTION ................................................................................................................... 4 MODELS .............

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; Only use replacement parts recommended by Pelco.

Pelco Manual C820M-D (1/01) 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel andconform to all local codes. 2. Unless the unit is specifically...

Page 4 - DESCRIPTION; MODELS

4 Pelco Manual C820M-D (1/01) DESCRIPTION The MS500 Series provides an inexpensive and reliable method of switching 4 to 18 inputsto a single monitor output using interlocked manual pushbuttons. Included in this series isthe MS540 switcher with two monitor outputs and the capacity to switch up to 40...

Page 5 - INSTALLATION; Plug in the power cord. The switcher will begin operating.; For the maximum; TERMINATING SWITCHERS; Video Coaxial Cable Requirements; Maximum Distance; MS500 Series Switchers - Terminating Configuration

Pelco Manual C820M-D (1/01) 5 INSTALLATION 1. Place the unit on a flat surface, or install it in an equipment rack using the appropriaterack-mount kit. 2. Refer to Figures 1 - 6 and select the desired configuration for your installation. Makeall equipment connections as illustrated in the drawings. ...

Page 6 - LOOPING SWITCHERS; Looping

6 Pelco Manual C820M-D (1/01) LOOPING SWITCHERS Use coaxial cable to connect the input and looping video cables to the appropriate inputconnectors. Connect the monitor(s) to the monitor output. (Refer to Figures 3 and 4.) IMPORTANT: Looping switchers do not have inter-nal termination. Inputs mustbe ...

Page 7 - SWITCHERS WITH AUDIO FOLLOW; Configuration does; SWITCHERS WITH BALANCED AUDIO FOLLOW; MS500 Series Switchers with Balanced Audio Follow

Pelco Manual C820M-D (1/01) 7 SWITCHERS WITH AUDIO FOLLOW MS500 Series models with “AF” in the suffix have a connection for an audio signal source.Using appropriate cable with compatible connectors, connect audio signal sources to RCAjack (refer to Figure 5). NOTE: Configuration does not permit two-...

Page 8 - SWITCHERS WITH AMPLIFIED OUTPUT; Use Monitor 2 non-amplified output only when interfacing with the; OPERATION; Units plugged into electrical outlets should be unplugged

8 Pelco Manual C820M-D (1/01) SWITCHERS WITH AMPLIFIED OUTPUT The MS540DT and MS540LDT switchers provide both an amplified output (Monitor 1) anda non-amplified output (Monitor 2). Most installations require the use of Monitor 2 output forproper operations. NOTE: Use Monitor 2 non-amplified output o...

Page 10 - SPECIFICATIONS; VIDEO

10 Pelco Manual C820M-D (1/01) SPECIFICATIONS VIDEO Inputs: 4, 8, 12, or 40 as indicated by the last two digits of the modelnumber. Video Connectors: BNC Audio Connectors: AF Switchers 1/8-inch RCA phone jack BAF Switchers Terminal block Termination: Terminated or Non-looping Switchers Input 75-ohm ...

Page 11 - GENERAL

Pelco Manual C820M-D (1/01) 11 GENERAL Switching: Interlocked manual pushbuttons Construction: Cover Steel, black polyester powder coat Chassis Steel, zinc plated Panel Aluminum, black polyester powder coat Environment: 32 ° to 120 ° F (0 ° to 48.89 ° C) Dimensions MS504 Series(except AFL,BAF, and B...

Page 12 - REVISION HISTORY

12 Pelco Manual C820M-D (1/01) REVISION HISTORY Manual # Date Comments C820M 3/88 Original version. C820M-A 9/90 Added to Warning Section for UL compliance. C820M-B 6/92 Revised to cover all MS500 Series models. Added DT200 to Options section. C820M-C 10/97 Revised Figures 1 and 2. Put into new form...

Pelco MS504BAFL - Manual

Table of Contents:

Summary

Other Pelco Models