Pelco MLZA6DT - Manual - manualsarea.com

Page 2 - ii

ii Pelco Manual C518M Rev B (4/91) TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................ 1 2.0 SCOPE ...........................................................................

Page 3 - prior to installation and operation.; The product may bear the following marks:; CAUTION; RISK OF ELECTRIC SHOCK.

Pelco Manual C518M Rev B (4/91) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 4. Only use replacement parts recommended byPelco. 5. After replacement/repair of this unit’s electricalcomponents, conduct a resistance measurementbetwee...

Page 5 - CONNECTOR ASSEMBLY; Connector Assembly

Pelco Manual C518M Rev B (4/91) 3 4.0 INSTALLATION 4.1 CONNECTOR ASSEMBLY Installation and/or testing will require you to assemblethe connector parts provided. Fabricate the intercon-necting cable according to the following steps (refer-ence Figure 1). 1. Slide part A of the cable clamp (item 1) ove...

Page 6 - Wiring Diagram for Output Pin Assignments; WHT

4 Pelco Manual C518M Rev B (4/91) Figure 2. Wiring Diagram for Output Pin Assignments *GROUND WIRE IS SOLDERED TO CONNECTOR HOUSING. CONTROL OUTPUT (CONA14P) P3 LENS INPUT (CONA5M) I R I S LENS COM ZOOM GND FOCUS RED BLK GRN WHT 10 13 12 8 11 1 4 2 G 3 YEL 1 3 12 14 1 2 6 3 5 4 WHT *

Page 7 - INSTALLATION; Disconnect the equipment from its power supply.

Pelco Manual C518M Rev B (4/91) 5 4.2 R300 RACK MOUNT KIT INSTALLATION The R300 Rack Mount Kit holds up to three controlmodules. Blank filler panels are provided for less thanthree modules. To convert desk top units, perform the following steps(refer to Figure 3): 1. Disconnect the equipment from it...

Page 8 - Basic System Configuration; COAX CABLE

6 Pelco Manual C518M Rev B (4/91) 5.0 OPERATION AND SYSTEM TEST 5.1 SYSTEM TEST FOR MLZA6DT 1. Hook up the cable between the output connectoron the MLZA6DT and the input connector on thelens (see Figure 4). 2. Connect the video cable from the camera to theVIDEO LOOP-THRU on the rear panel and to the...

Page 9 - and you will

Pelco Manual C518M Rev B (4/91) 7 6.0 MAINTENANCE Under normal operating conditions and usage, mainte-nance of this equipment is not necessary. However, ifmaintenance should be required, consult Pelco or aqualified service technician. NOTE: Pelco offers a 24-hour, seven-days- a-week Technical Assist...

Page 10 - MLZA6DT Schematic

8 Pelco Manual C518M Rev B (4/91) 7.0 SCHEMATIC Figure 5. MLZA6DT Schematic BLK BLU BLU BLK VIDEO LOOP-THR U 1 2 R2 C8 .05 1.5K 500V R1 15M C13 .01MF CR7 CR8 R22 15M R3 2.7M R4 430 Q3 2N5457 R23 3.9K VIDEO AMP B- B+ B- B+ R25 1.2K Q5 MPC 6527 R26 330K Q6 2N2907 R28 4.7K R29 47K LEVEL ADJUST R74 2.5K...

Page 11 - MLZA6DT Dimension Drawing

Pelco Manual C518M Rev B (4/91) 9 8.0 SPECIFICATIONS CONTROLS Zoom: Paddle switch TELE/WIDE Focus: Paddle switch NEAR/FAR Manual Iris: Paddle switch OPEN/CLOSE Auto-Iris: Paddle switch AUTO/MANUAL Speed: Knob adjustment Video Level: Knob adjustment On/Off: Rocker switch Pilot Lamp: Long life neon EL...

Page 12 - WARRANTY

10 Pelco Manual C518M Rev B (4/91) 9.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proveddefective in material or workmanship for a period of one year after the dateof shipment. Exceptions to this warranty are as noted below: • Five years on...

Pelco MLZA6DT - Manual

Table of Contents:

Summary

Other Pelco Models