Pelco ICS210 - Manual - manualsarea.com

Page 2 - Contents; List of Illustrations

2 C2491M-C 1/06 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 3 - Important Safety Instructions; maximum specified load.; RISK OF ELECTRIC SHOCK.

C2491M-C (1/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such...

Page 4 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE

4 C2491M-C (1/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 5 - Description

C2491M-C (1/06) 5 Description The ICS210 Series Camclosure ® is a wedge style integrated camera system that is quick and easy to install. The system is designed to mount directly to a wall or ceiling, or to a corner with the ICS210- CM corner mount. ICS210 system is shipped fully assembled. System c...

Page 6 - Installation; PREPARE MOUNTING SURFACE; three tamperproof screws, and then lift the cover from the base.

6 C2491M-C (1/06) Installation PREPARE MOUNTING SURFACE 1. Remove the cover of the ICS210. Use the screwdriver bit that is provided to loosen the three tamperproof screws, and then lift the cover from the base. 2. Remove the camera assembly from the base by removing the Phillips screws on each side ...

Page 8 - INSTALL BASE; WITHOUT CONDUIT; WITH CONDUIT; Prepare the conduit for the installation.; Adjustable mounting pattern only :

8 C2491M-C (1/06) INSTALL BASE WITHOUT CONDUIT 1. Pull the power and video wiring for the camera through the mounting surface and then through the wiring hole in the mounting plate. Fasten the mounting plate to the mounting surface with #8 stainless steel screws (not provided) of the appropriate len...

Page 9 - Pull the wiring inside the base.

C2491M-C (1/06) 9 3. Using a blunt tool push out the wiring plug in the bottom of the base (refer to Figure 6). Pull the wiring inside the base. Figure 6. Removing the Wiring Plug 4. Insert the hole plug that is supplied into the hole in the base of the Camclosure (refer to Figure 7). Figure 7. Inst...

Page 10 - wires and video cable back through the conduit fitting.; REINSTALL CAMERA MODULE

10 C2491M-C (1/06) 6. Install a 3/4-inch (1.91 cm) conduit connector in the conduit opening. Line up the mounting holes in the base with the mounting holes of the mounting plate. Attach the base to the mounting plate with the three 8-32 x 0.375-inch screws and lock washers previously removed. 7. Att...

Page 11 - ADJUST POSITION; Turn on power to the camera and monitor.; Varifocal lens only:; Loosen the focal length and focus locking screws (refer to; REPLACE COVER

C2491M-C (1/06) 11 ADJUST POSITION 1. Turn on power to the camera and monitor. 2. Varifocal lens only: Loosen the focal length and focus locking screws (refer to Figure 9). Adjust according to scene detail. Retighten the screws. Figure 9. Varifocal Lens Adjustment 3. Adjust the position of the camer...

Page 12 - same transformer, this should solve the problem.; FIXED LENS

12 C2491M-C (1/06) Adjustments (Color Camera Only) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however, adjustments may be necessary. 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vertical phase, iri...

Page 13 - AUTO IRIS LEVEL ADJUSTMENT; Move the screw in the slot to bring the picture into focus.

C2491M-C (1/06) 13 AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fixed focal length lens with an auto iris, you can adjust the iris level setting to increase or decrease brightness. Figure 11. Iris Level Adjustment FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS To adjust th...

Page 14 - HEATER BOARD REMOVAL; Wait for the heater elements to cool if they are hot.

14 C2491M-C (1/06) HEATER BOARD REMOVAL To remove the heater board, do the following: 1. Disconnect the four-pin heater connector (red, orange, and black wires) if it is plugged in. Figure 13. Removing Heater Board 2. Wait for the heater elements to cool if they are hot. 3. Apply pressure and press ...

Page 16 - SWITCH SETTINGS FOR VARIFOCAL LENS; AE Functions

16 C2491M-C (1/06) SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. Figure 16. Switch Settings for Varifocal Lens For manually setting and locking the white balance Place a white background in front ...

Page 17 - Specifications; General

C2491M-C (1/06) 17 Specifications General Pan/Tilt Adjustment Manual; 5° above horizontal to 20° below horizontal tilt; 24° pan adjustment when using the adjustable mounting pattern in base Rating Meets NEMA Type 4X and IP66 standards Construction Aluminum mounting plate, base, and cover, steel came...

Page 18 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic...

Pelco ICS210 - Manual

Table of Contents:

Summary

Other Pelco Models