Pelco HS4514-2 - Manual
Pelco HS4514-2 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – OPTIONAL –
- Page 3 – Maxim; Table A. 24 VAC Wiring Distances; otal vA consumed
- Page 4 – Figure 1. HS4514 Series Input Wiring Diagram
- Page 5 – PELCO; Figure 2. Circuit Board Component Locations; Maximum Distance
- Page 6 – You can damage your; DO NOT
- Page 7 – TROUBLESHOOTING; Reverse the procedure to close.; MAINTENANCE; MECHANICAL; Heater is thermostatically controlled to activate ON at 42
- Page 8 – REVISION HISTORY; Date; Revised certifications.; GENERAL; Gray polyester powder coat; PRODUCT WARRANTY AND RETURN INFORMATION; WARRANTY
Pelco Manual C1472M-C (10/05)
1
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1.
Installation and servicing should only be done by qualified service personnel and conform
to all local codes.
2.
Only use replacement parts recommended by Pelco.
3.
After replacement/repair of this unit’s electrical components, conduct a resistance
measurement between line and exposed par ts to verify the exposed par ts have not been
connected to line circuitry.
4.
The installation method and materials should be capable of supporting four times the
weight of the enclosure, pan/tilt, camera and lens combination.
The product may bear the following marks:
This symbol indicates that
dangerous voltage constituting a
risk of electric shock is present
within this unit.
This symbol indicates that there
are important operating and
maintenance instructions in the
literature accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.
NOTE: Heaters in models HS4514-1 and HS4514-2 have not been evaluated by UL.
DESCRIPTION
The HS4514 Series are high security environmental enclosures designed for use with 1/3-inch
CCD format cameras with fixed auto iris or motorized zoom lenses. The enclosures are
designed to withstand, without penetration, rounds fired from a .357 Magnum handgun from
a distance of 15 feet (4.57 m). The enclosures are designed to meet the UL 752 Level 2 bullet-
resisting standard, and the viewing window is designed to meet the UL 752 Level 3 bullet-
resisting standard.
The viewing window absorbs the full ballistic impact without penetration and will not pulverize
or spall into sharp, dangerous shards.
Constructed from steel to provide maximum protection and durability, the HS4514 Series
enclosures are engineered for ease of installation and service. The removable top allows
convenient access to the camera and lens for periodic servicing and/or adjustments. The
HS4514 Series also features a removable camera sled that can be inverted to accommodate
various camera and lens combinations. Tamper-resistant screws secure the enclosure cover.
The HS4514-1/-2/-3 enclosures are equipped with a factory-installed, thermostatically controlled
heater.
The HS4514 Series is designed for fixed mount applications.
Models
HS4514
High security, environmental enclosure
HS4514-1
Same as HS4514 except with 120 VAC thermostatically controlled heater
HS4514-2
Same as HS4514 except with 24 VAC thermostatically controlled heater
HS4514-3
Same as HS4514 except with 230 VAC thermostatically controlled heater
C1472M-C (10/05)
HS4514 Series
High Security Enclosure
3500 Pelco Way
Clovis, CA 93612-5699
USA
In North America & Canada:
Tel (800) 289-9100
FAX (800) 289-9150
International Customers:
Tel (1-559) 292-1981
FAX (1-559) 348-1120
www.pelco.com
®
C A U T I O N :
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Pelco Manual C1472M-C (10/05) INSTALLATION The following items are supplied: 1 HS4514 Series enclosure 1 #10 socket for tamper-resistant screws (1/4-inch drive tool not provided) 1 Three-pin plug with leads (included with heater -1/-2/-3 models) 2 1/4-20 Phillips head screws (to mount enclosure) 1...
Pelco Manual C1472M-C (10/05) 3 Enclosure Power If the enclosure does not have a heater (model HS4514), proceed to the Camera Mounting section. If your enclosure has a heater (models HS4514-1/-2/-3), follow the steps below. 1. Add the camera’s wattage to the wattage of the heater. Refer to the Speci...
4 Pelco Manual C1472M-C (10/05) NOTE: THE MODEL NUMBERS OF OPTIONAL ACCESSORIES MA TCH ENCLOSURE INPUT VOL TAGE NUMBER SYSTEM. XXXX – 1 IS 120 V A C – 2 IS 24 V A C – 3 IS 230 V A C OPTIONAL CAMERA POWER (SUPPLIED WITH PCB)** ACCESSOR Y: O/I-OUTLET OUTLET PLUG 120V CAMERA POWER 24/120/230 V A C (SUP...
