Pelco FX82012 - Manual

6 C2624M (6/07) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired ...

C2624M (6/07) 7 Product Overview DESCRIPTION The FX82012 unmanaged Ethernet switch provides one 10BASE-T/100BASE-TX port and two 100BASE-FX fiber ports for the transport of bidirectional Ethernet data. Available in multimode and single-mode versions, the fiber ports use wavelength division multiplex...

C2624M (6/07) 9 MODELS The FX82012 module consists of the following series of models: Multimode Models:* FX82012MSTR-2 Unmanaged Ethernet switch, one 10BASE-T/100BASE-TX port, two multimode ST fiber ports, one fiber per port (total of two fibers) FX82012MSCR-2 Unmanaged Ethernet switch, one 10BASE-T...

10 C2624M (6/07) FRONT PANEL Figure 3 illustrates the front panel of the FX82012 module. Figure 3. Front Panel of FX82012 Module For detailed information about the front-panel LEDs, refer to the Troubleshooting section. ì RESET BUTTON (restarts the unit) î FIBER FAILOVER (REDUNDANCY) MODE LED ï 100B...

C2624M (6/07) 11 REAR PANEL Figure 4 illustrates the rear panel of the FX82012 module. Figure 4. Rear Panel of FX82012 Module (SC Fiber Connectors Shown) For additional information about rear-panel connections, refer to the Installation section. For detailed information about the RJ-45 LEDs, refer t...

12 C2624M (6/07) Installation PACKAGE CONTENTS The following items are supplied: 1 FX82012 module 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4-40 x 0.250-i...

C2624M (6/07) 13 Using the TX Mode switch, you can do the following: • Enable autonegotiation or select (force) a specific data rate and duplex mode: – Enabling autonegotiation allows the FX82012 module to automatically negotiate with the device to which the port is connected for data rate and duple...

14 C2624M (6/07) SETTING FIBER FAILOVER MODE NOTE: As a matter of convenience, it is recommended that you set fiber failover (redundancy) mode—if required—before mounting the FX82012 module into a rack or onto a wall. Fiber failover mode is disabled by default. The FX82012 module can operate in fibe...

C2624M (6/07) 15 Table B. FX Mode Switch Settings MOUNTING The FX82012 module can be mounted into a rack or can be used as a stand-alone module. As a stand-alone module, the unit can be placed on a desktop or can be mounted to a wall. NOTE: As a matter of convenience, it is recommended that you set ...

16 C2624M (6/07) MOUNTING THE FX82012 MODULE TO A WALL The FX82012 module can be mounted to a wall in the following ways: • Using the supplied wall clip for attachment of a single module to a wall. For installation instructions, refer to the Mounting the FX82012 Module Using the Wall Clip section. •...

18 C2624M (6/07) CONNECTIONS Connections to the FX82012 module are made on the rear panel of the module (refer to Figure 8). Figure 8. FX82012 Connections (SC Fiber Connectors Shown) As illustrated in Figure 8, FX82012 connections consist of the following: • Power connection – A 12 VDC or 24 VAC pow...

22 C2624M (6/07) Troubleshooting LED indicators on the front and rear panels of the FX82012 module allow you to monitor operational status: • LED indicators on the front panel allow you to monitor operating power, fiber redundancy mode status, 100BASE-FX port status, and optic signal/laser status. R...

C2624M (6/07) 31 Specifications PERFORMANCE Switch Type Unmanaged Layer 2 Switch Method Store and forward Switch Fabric Non-head-of-line blocking Data Rate 10/100 Mbps Compliance IEEE 802.3, 802.3u, 802.3x Interface Auto MDI/MDI-X Operating Mode Half-duplex or full-duplex Address Table Size 1,024 MA...

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3...