Pelco FR85081 - Manual

6 C1648M (4/05) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired ...

C1648M (4/05) 7 Product Overview DESCRIPTION The FT85081/FR85081 fiber transmitter and receiver provide the ability to transmit eight unidirectional composite video channels and one bidirectional data channel over one optical fiber (refer to Figure 1). Figure 1. Eight-Channel Video FT85081 Transmitt...

8 C1648M (4/05) MODELS The FT85081/FR85081 fiber transmitter and receiver consist of the following series of models: Multimode Models: FT85081MSTR Eight-channel fiber optic video transmitter/single-channel data transceiver; multimode, ST connector FR85081MSTR Eight-channel fiber optic video receiver...

C1648M (4/05) 9 FRONT PANEL The front panel of the FT85081 transmitter and the FR85081 receiver provides LED indicators that allow you to monitor data activity, signal status, and operating power. The following sections provide a view of the front panel of the FT85081 transmitter and the FR85081 rec...

C1648M (4/05) 11 REAR PANEL Connections to the FT85081 transmitter and the FR85081 receiver are made to the rear panel of the module. The following sections provide a view of the rear panel of the FT85081 transmitter and the FR85081 receiver. REAR PANEL - FT85081 TRANSMITTER Figure 4 illustrates the...

C1648M (4/05) 13 Installation PACKAGE CONTENTS The following items are supplied: • With the FT85081 transmitter: 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC input, 12 VDC output 1 Wall clip with two 4-40 x .2...

14 C1648M (4/05) With the FT85081 transmitter/FR85081 receiver powered off, turn the Data Selection switch using a screwdriver until the number representing the required data communication is selected. Refer to Table A for Data Selection switch settings. Note the following: • The FT85081 transmitter...

C1648M (4/05) 15 • RK5000PS-5U: Designed to accommodate Endura ™ modules but can also accommodate fiber optic modules with the use of the appropriate adapter kit. The RK5003-1UEXP adapter kit is required for installation of the FT85081 transmitter/FR85081 receiver into the RK5000PS-5U chassis.For in...

16 C1648M (4/05) CONNECTIONS Connections to the FT85081 transmitter and the FR85081 receiver are made on the rear panel of the modules and consist of the following: • Power connection NOTE: A 12 VDC or 24 VAC power supply can be used to power the transmitter/receiver when used as a standalone module...

24 C1648M (4/05) Troubleshooting LED indicators on the front panel of the FT85081 transmitter/FR85081 receiver (refer to Figure 2 and Figure 3, respectively) allow you to monitor signal status, data activity, and operating power. Table C provides information about the front-panel indicators and asso...

C1648M (4/05) 25 Video Present LED (Continued) Red on receiver Incoming video signal is not present on the channel. Optical signal is not being received from the transmitter. Carrier Detect LED is also red. Refer to the Carrier Detect LED troubleshooting section below. Video source is not powered on...

28 C1648M (4/05) Specifications VIDEO Number of Channels 8 Modulation Type Pulse code modulation, 8-bit resolution Video Input 1.0 Vp-p, 75 ohms; NTSC, PAL, and SECAM Bandwidth 6.5 MHz Gain Unity Crosstalk -50 dB typical at 3.58 MHz Differential Gain <1% Differential Phase <1.2° Tilt <1% Si...

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic...