Page 4 - Important Safety Instructions
4 C2653M (6/07) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manu...
Page 5 - RISK OF ELECTRIC SHOCK.
C2653M (6/07) 5 The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying...
Page 6 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE
6 C2653M (6/07) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired ...
Page 7 - Product Overview; DESCRIPTION
C2653M (6/07) 7 Product Overview DESCRIPTION The FT82011/FR82011 Ethernet media converter converts 10BASE-T/100BASE-TX data to 100BASE-FX data and vice versa. Designed for point-to-point applications, the FT82011/FR82011 media converter provides one 10BASE-T/100BASE-TX port and one 100BASE-FX fiber ...
Page 9 - MODELS; OPTIONAL ACCESSORIES
C2653M (6/07) 9 MODELS The FT82011 and FR82011 modules consist of the following series of models: Multimode Models:* FT82011MSTR-1 Ethernet media converter, one 10BASE-T/100BASE-TX port, one multimode ST fiber port, one fiber, fiber optic compatibity with FR82011MSTR-1 and other multimode ST Pelco E...
Page 10 - FRONT PANEL
10 C2653M (6/07) FRONT PANEL Figure 2 illustrates the front panel of the FT82011 and FR82011 modules. Figure 2. Front Panel of FT82011 and FR82011 Modules For detailed information about the front-panel LEDs, refer to the Troubleshooting section. ì RESET BUTTON (restarts the unit) î 100BASE-FX STATUS...
Page 11 - REAR PANEL
C2653M (6/07) 11 REAR PANEL Figure 3 illustrates the rear panel of the FT82011 and FR82011 modules. Figure 3. Rear Panel of FT82011 and FR82011 Modules (SC Fiber Connector Shown) For additional information about rear-panel connections, refer to the Installation section. For detailed information abou...
Page 12 - PACKAGE CONTENTS
12 C2653M (6/07) Installation PACKAGE CONTENTS The following items are supplied: 1 FT82011 or FR82011 module 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4-4...
Page 14 - MOUNTING
14 C2653M (6/07) MOUNTING The FT82011/FR82011 module can be mounted into a rack or can be used as a stand-alone module. As a stand-alone module, the unit can be placed on a desktop or can be mounted to a wall. NOTE: As a matter of convenience, it is recommended that you set the modes of operation fo...
Page 16 - CONNECTIONS
16 C2653M (6/07) CONNECTIONS Connections to the FT82011/FR82011 module are made on the rear panel of the unit (refer to Figure 6). Figure 6. FT82011/FR82011 Module Connections As illustrated in Figure 6, FT82011/FR82011 connections consist of the following: • Power connection NOTES: – A 12 VDC or 24...
Page 18 - Troubleshooting; Indicator
18 C2653M (6/07) Troubleshooting LED indicators on the front and rear panels of the FT82011/FR82011 module allow you to monitor operational status: • LED indicators on the front panel allow you to monitor operating power, 100BASE-FX port status, and optic signal/laser status. Refer to Table B for in...
Page 27 - Specifications; PERFORMANCE
C2653M (6/07) 27 Specifications PERFORMANCE Switch Type Unmanaged Layer 2 Switch Method Store and forward Data Rate 10/100 Mbps Compliance IEEE 802.3, 802.3u, 802.3x Interface Auto MDI/MDI-X Operating Mode Full-duplex or half-duplex Address Table Size 1,024 MAC address entries with automatic learnin...
Page 31 - PRODUCT WARRANTY AND RETURN INFORMATION
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3...