Pelco E708-24PS - Manual
Pelco E708-24PS – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – To install the camera and lens, perform the following steps:; Wire Gauge; Video Coaxial Cable Requirements; Maximum Distance; 4 VAC Wiring Distances
- Page 3 – MECHANICAL; Enclosure Assembly; Do not
- Page 4 – REVISION HISTORY; Date; PRODUCT WARRANTY AND RETURN INFORMATION
C415M-J (11/99)
E700 Series
Dust-Tight Enclosure
®
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1.
Installation and servicing should only be done by qualified service personnel and conform
to all local codes.
2.
Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclo-
sure, it is designed for indoor use only and it must not be installed where exposed to rain
and moisture.
3.
Only use replacement par ts recommended by Pelco.
4.
After replacement/repair of this unit’s electrical components, conduct a resistance mea-
surement between line and exposed par ts to verify the exposed par ts have not been con-
nected to line circuitry.
The product and/or manual may bear the following marks:
Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.
This symbol indicates that danger-
ous voltage constituting a risk of
electric shock is present within
this unit.
This symbol indicates that there
are impor tant operating and main-
tenance instructions in the litera-
ture accompanying this unit.
3500 Pelco Way,
Clovis, CA 93612-5699
USA
In North America & Canada:
Tel (800) 289-9100
FAX (800) 289-9150
International Customers:
Tel +1 (559) 292-1981
FAX +1 (559) 348-1120
www.pelco.com
C A U T I O N :
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
DESCRIPTION
The E700 Series Dust-Tight Enclosure is designed to protect CCTV cameras operating in
small-particle and dusty environments. Stainless steel models are available for use in corro-
sive atmospheres.
Models
E706-16
6-inch diameter x 16-inch length (15.24 cm x 40.64 cm), aluminum con-
struction
E706-16P
Same as E706-16, except with purge fittings (15.24 cm x 40.64 cm)
E706-16PS
Same as E706-16P, except type 304 stainless steel construction
E706-16S
Same as E706-16, except type 304 stainless steel construction
E706-24
6-inch diameter x 24-inch length (15.24 cm x 60.96 cm), aluminum con-
struction
E706-24P
Same as E706-24, except with purge fittings
E706-24PS
Same as E706-24P, except type 304 stainless steel construction
E706-24S
Same as E706-24, except type 304 stainless steel construction
E708-24
8-inch diameter x 24-inch length (20.32 cm x 60.96 cm), aluminum con-
struction
E708-24P
Same as E708-24, except with purge fittings
E708-24PS
Same as E708-24P, except type 304 stainless steel construction
E708-24S
Same as E708-24, except type 304 stainless steel construction
NOTE:
Models with purge
fittings require a filtered
compressed air supply up
to 35 psi at 10 cfm to pro-
vide positive internal air
pressure circulation. Uses
1/4-inch NPT fittings.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
INSTALLATION Camera and Lens To install the camera and lens, perform the following steps: 1. Unsnap the two latches holding the rear end plate on the enclosure and slide the camerasled out. 2. Place the camera and lens at the maximum forward position on the sled. Adjust thecamera and lens so that th...
Enclosures with Purge Fittings Purge fittings create internal positive pressure, keeping external contaminants from enteringthe enclosure. Proper installation requires a filtered compressed air supply up to 35 psi at 10cfm. A refrigerated air supply will provide additional cooling for the enclosure....
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved. Endura and ExSite are trademarks of Pelco.Lucite is a registered trademark of DuPont. REVISION HISTORY Manual # Date Comments C415M-H 5/96 Revision ...
