Pelco DX8100-ISCI - Manual
Pelco DX8100-ISCI – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Tips; Removing Power Cord from Wall
- Page 3 – Move the Main Capture Card to slot 3.; PREPARING THE DX8100 FOR SCSI CARD INSTALLATION; OPENING THE DX8100 CHASSIS; strap before attempting to open the DX8100 chassis cover.
- Page 4 – UNDERSTANDING THE DX8100 COMPONENT LAYOUT; Item Description
- Page 5 – MOVING THE MAIN CAPTURE CARD TO SLOT 3; Move the main Capture Card from slot 2 to slot 3:
- Page 6 – Moving Main Capture Card; INSTALLING THE DX8100 SCSI CARD; To install the SCSI card into slot 2:
- Page 7 – SATABoy. For information about reassembling the unit, refer to; REASSEMBLING THE UNIT; a. Remove the paper backing from the product label.
- Page 8 – equipment you removed earlier.; SETTING UP THE SATABOY; For New SATABoy Only:; Install the HDs into the SATABoy system:
- Page 9 – Connect to a PC and SATABoy with Cat5 Crossover cable.; For New SATABoy with 8 or 14 HDs: Configure Computer; on the desktop and then left click
- Page 10 – Figure 4; Configure SATABoy with 8 or 14 HDs; Open the Internet Explorer; Enter; under the main menu.
- Page 12 – Use the following IP address; Resume SATABoy Configuration with 8 or 14 HDs; Open the Internet Explorer on the desktop.
- Page 13 – Figure 7
- Page 15 – Enter the name for the new volume
- Page 16 – Create Volume
- Page 17 – Open the Computer Management by selecting the
- Page 18 – Select Disk to Convert; Next; next to Disk2 and select; New Partition
- Page 19 – Extended partition; and click; and; Finish
- Page 21 – Apply the Labels
Tech
Tech
Tips
Helpful Tips for Pelco Products
World Headquarters
3500 Pelco Way, Clovis, California 93612 USA
USA & Canada Tel: 800/289-9100 Fax: 800/289-9150
International Tel: 1-559/292-1981 Fax: 1-559/348-1120
www.pelco.com
Pelco and the Pelco logo are registered trademarks of Pelco, Inc.
Information subject to change without notice.
©Copyright 2008, Pelco, Inc. All rights reserved.
Page 1 of 21 DX8100-ISCI_SCSI_CARD_SATABoy.fm
INSTALLING THE DX8100-ISCI SCSI CARD
WITH SATABOY
April 16, 2008
TOOLS NEEDED
GETTING READY
Before you install the DX8100-ISCI SCSI card, familiarize yourself with the instructions in this Tech
Tip. The steps to install the external video storage upgrade are summarized as follows:
1. Unpack the DX8100-ISCI kit and check that you have all the necessary kit components.
2. Verify that you have the required tools to install the SCSI card. For information about the tools
required to install the SCSI card, refer to Tools Needed table above.
3. Shut down the DX8100 Series DVR. For information about shutting down the DX8100, refer to the
DX8100 Installation Manual, Operation and Programming manual, or DX8100 Server online Help.
4. Unplug the power cord from the wall socket.
WARNING:
It is critical that the unit be unplugged for your safety. You must remove the power
cord because current continues to flow through the DX8100 even when the unit is off. Remove
the power cord from the wall socket first, and then from the rear of the DVR.
Qty
Description
1
Phillips screwdriver #1 (nonmagnetic)
1
Properly grounded electrostatic discharge (ESD) wrist
strap and mat
4
Small containers for storing screws (optional)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Tech Tech Tips Helpful Tips for Pelco Products World Headquarters 3500 Pelco Way, Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150International Tel: 1-559/292-1981 Fax: 1-559/348-1120www.pelco.com Pelco and the Pelco logo are registered trademarks of Pelco, Inc. Info...
Tech Tech Tips Helpful Tips for Pelco Products World Headquarters 3500 Pelco Way, Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150International Tel: 1-559/292-1981 Fax: 1-559/348-1120www.pelco.com Pelco and the Pelco logo are registered trademarks of Pelco, Inc. Info...
Tech Tech Tips Helpful Tips for Pelco Products World Headquarters 3500 Pelco Way, Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150International Tel: 1-559/292-1981 Fax: 1-559/348-1120www.pelco.com Pelco and the Pelco logo are registered trademarks of Pelco, Inc. Info...
