Pelco CM9700UTP32A - Manual

Page 3 - Contents

C3646M-C (6/09) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Regulatory Notices . . . . . . . . . . . . . . . . . . . ...

Page 5 - Important Safety Instructions; be installed where exposed to rain and moisture.

C3646M-C (6/09) 5 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the ma...

Page 6 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE; Reorient or relocate the receiving antenna.

6 C3646M-C (6/09) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 7 - Description; Models; Parts List; Qty; CM9700UTP Series Installation manual

C3646M-C (6/09) 7 Description The CM9700UTP Series multichannel active receiver is a 16- or 32-channel unit that can receive live video over unshielded twisted pair (UTP) cable. The front panel of each model contains a dial and a LED per channel; dials are used for selecting cable distance. The back...

Page 8 - FRONT PANEL; Distance Rotary Switch:; Indicates that color video is being received.; Fan Alarm Indicators:; Glow red when an alarm triggers due to a fan failure.

8 C3646M-C (6/09) FRONT PANEL Figure 1. CM9700UTP16A Front Panel Figure 2. CM9700UTP32A Front Panel ì Pelco Badge: Glows blue when the unit has power. When the temperature rises above the specified temperature (95°F [35°C]), or when any of the fans fail, the Pelco badge LED will blink and a buzzer w...

Page 9 - BACK PANEL; Ribbon Cable Connectors:; Connects to a CM9700 Series matrix for video output.

C3646M-C (6/09) 9 BACK PANEL Figure 3. CM9700UTP16A Back Panel Figure 4. CM9700UTP32A Back Panel ì AC Power Connector: Connects the UTP receiver to the mains power supply (100 to 240 VAC, 50 to 60 Hz, autoranging). î BNC Connectors: There are 16 or 32 coaxial video outputs (depending on model) for e...

Page 10 - Installation; RACK MOUNTING; RJ-45 Connector Pins; Pin

10 C3646M-C (6/09) Installation RACK MOUNTING Install the CM9700UTP Series active receiver in a standard 19-inch (48.26 cm) equipment rack using standard mounting hardware (10-32 cage nuts and 10-32 x 0.50-inch Phillips pan head screws, supplied). The receiver is one rack unit (1 RU) high. DESKTOP M...

Page 12 - INSTALLING THE JUMPERS FOR CE COMPLIANCE (ONLY CM9700UTP16A); Unplug the unit to turn off the power.; INSTALLING THE JUMPERS FOR CE COMPLIANCE (ONLY CM9700UTP32A); To meet CE compliance standards, jumpers

12 C3646M-C (6/09) INSTALLING THE JUMPERS FOR CE COMPLIANCE (ONLY CM9700UTP16A) 1. Unplug the unit to turn off the power. 2. Unscrew the six, black 4-40 x 0.25-inch Phillips flat head screws that secure the cover to the chassis. 3. Remove the cover. 4. Install the 16 jumpers on the pins; use one for...

Page 13 - COLOR VIDEO RANGE SETTINGS; Advance Color Video Signal Settings; Cable Length

C3646M-C (6/09) 13 COLOR VIDEO RANGE SETTINGS For optimal tuning, adjust the rotary switch located on the front panel to the correct color video range position. Refer to Figure 8 and Table D, and then complete the following steps: 1. Plug the power cord into a power source to turn on the unit. The L...

Page 14 - Gain; Low

14 C3646M-C (6/09) BLACK-WHITE OR DAY/NIGHT VIDEO SETTINGS For the best picture quality, adjust the DIP switch settings. Refer to Figure 9 and Table E, and then complete the following steps: 1. Plug the power cord into a power source to turn on the unit. When the input video signal is present, the L...

Page 15 - Configuration; Color; Required Equipment; Video signal generator; ADVANCE COLOR VIDEO SIGNAL SETTINGS; Color Burst and

C3646M-C (6/09) 15 Configuration This section describes an optional advanced tuning procedure for troubleshooting a video path. For most installations, the steps detailed in Color Video Range Settings on page 13 should be sufficient to set up the unit. Required Equipment • Video signal generator • O...

Page 17 - Maintenance; Specifications; FAN FILTER: CLEANING OR REPLACING; Remove the filter and inspect it for wear and physical damage.

C3646M-C (6/09) 17 Maintenance For proper ventilation, use the following instructions to maintain the fan filter and fan. For information about the operating temperature range, refer to Specifications on page 20. FAN FILTER: CLEANING OR REPLACING Filters can be cleaned and reused, or they can be rep...

Page 18 - FAN REPLACEMENT; Fan guard and filter

18 C3646M-C (6/09) FAN REPLACEMENT Fans maintain the unit’s internal temperature within the specified range if the ambient operating temperature is at or below 95°F (35°C). Fans are removable and field replaceable. If a fan fails, the Pelco badge LED will flash, an alarm will sound, and the fan’s in...

Page 20 - VIDEO

20 C3646M-C (6/09) Specifications VIDEO Video Standards NTSC/PAL/EIA/CCIR composite Video Output CM9700UTP16A 16 BNC and 1 ribbon cable connector CM9700UTP32A 32 BNC and 2 ribbon cable connectors Frequency Response 50 Hz to 6 MHz Common Mode/Differential Mode Rejection >60 dB Video Output 1.2 Vp-...

Page 23 - PRODUCT WARRANTY AND RETURN INFORMATION

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disp...

Pelco CM9700UTP32A - Manual

Table of Contents:

Summary

Other Pelco Models