Pelco CC1400HZ16-4 - Manual

DESCRIPTION

The CC1400HZ16-* Series DSP Color CCD
Camera combines high resolution imaging
and a built-in lens in a compact package.
This DSP (Digital Signal Processing) camera
uses a 1/4-inch color CCD (charged coupled
device) interline transfer sensing element.
The built-in lens has a maximum zoom ratio
of 128X (16X optical and 8X digital).

The telephoto (zoom in), white balance, and
wide angle (zoom out) controls are push but-
tons located on the back of the camera.
When you press and hold the telephoto but-
ton, the camera reaches maximum optical
magnification (16X). If you continue to press
and hold the telephoto button, the camera
automatically goes into 8X digital zoom. Auto
focus is enabled during zoom lens setup. The
white balance control renders colors based
on the amount of white in the scene. Once
you set the white balance, the camera holds
the setting until you adjust the white balance
again.

Additional adjustments can be made by con-
necting the camera to a personal computer
through an RS-422 cable interface. For infor-
mation about adjusting the camera through
an RS-422 interface cable, please contact
the factory.

MODELS

CC1400HZ16-2

NTSC format camera,
24 VAC

CC1400HZ16-4

NTSC format camera,
12 VDC

CC1400HZ16-* Series

DSP
Color
CCD Camera

® Pelco and the Pelco logo

are registered trademarks of Pelco.

© Copyright 2004, Pelco. All rights reserved.

®

SAFEGUARDS AND WARNINGS

Prior to installation and use of this product,
the following WARNINGS should be observed.

1.

Installation and servicing should only be
done by qualified service and installation
personnel.

2.

Installation shall be done in accordance
with all local and national electrical and
mechanical codes utilizing only approved
materials.

3.

Use only installation methods and
materials capable of supporting four
times the maximum specified load.

This symbol indicates that there
are impor tant operating and main-
tenance instructions in the litera-
ture accompanying this unit.

Please thoroughly familiarize yourself with
the information in this manual prior to instal-
lation and operation.

SPECIFICATIONS

General

Imaging Device

Color 1/4-inch interline
transfer CCD

Signal System

NTSC

Pixels

768 (H) x 508 (V)

Scanning System

2:1 interlace

Sync System

12 VDC

Internal
synchronization

24 VAC

External AC line lock

Horizontal Resolution 470 TV lines
Signal-to-Noise Ratio >46 dB
Minimum Illumination 1.0 lux, F1.6, 30 IRE,

AGC on, 89.9%
reflectance

Gain Control

Automatic

Exposure

Automatic
(1/60–1/10,000)

White Balance

Push to set auto

Focal Length

3.9 to 63 mm

Zoom Ratio

16X optical, 8X digital
(total 128X)

Minimum
Focus Distance

0.01m (wide angle),
1.20m (telephoto)

Focus Mode

Auto focus

Iris Control

Automatic

Camera Control

RS-422 cable
interfaced with PC

Electrical

Power Requirements

CC1400HZ16-2

24 VAC, 50/60 Hz

CC1400HZ16-4

12 VDC, 50/60 Hz

Power Consumption

CC1400HZ16-2

6 watts maximum
(camera only)

CC1400HZ16-4

4.7 watts maximum
(camera only)

Video Output

Composite output,
75 ohms terminated

3500 Pelco Way • Clovis, CA 93612-5699 • USA

In North America and Canada:

Tel (800) 289-9100 or FAX (800) 289-9150

International Customers:

Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120

www.pelco.com

Environmental

Operating
Temperature

32

°

-113

°

F (0

°

-45

°

C)

Storage
Temperature

32

°

-140

°

F (0

°

-60

°

C)

Humidity

0%-80% relative
humidity

Physical

Construction

Aluminum case

Finish

Neutral gray

Dimensions

CC1400HZ16-2

2.36 (H) x 2.27 (W) x
5.63 (L) inches
(5.99 x 5.77 x 14.30
cm)

CC1400HZ16-4

2.36 (H) x 2.27 (W) x
4.42 (L) inches
(5.99 x 5.77 x 11.20
cm)

Weight

12 VDC

0.75 lb (0.34 kg)

24 VAC

0.95 lb (0.43 kg)

(Design and product specifications

subject to change without notice.)

C1960M-A