Page 2 - Contents
2 C613M-A (5/05) Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description . . . . . . . . . . . . . . . . . . . . ....
Page 4 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE
4 C613M-A (5/05) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired...
Page 5 - PARTS LIST; Qty
C613M-A (5/05) 5 Description The SP04-140 is a special version of the single-input NET5301T video encoder. It is a high-performance, dual-stream, dual-input video encoding unit. Its main function is to convert live analog video from two cameras into dual MPEG-4 video streams. It transmits these stre...
Page 6 - PRODUCT SERIAL NUMBER LABEL PLACEMENT
6 C613M-A (5/05) PRODUCT SERIAL NUMBER LABEL PLACEMENT Product serial number labels help Pelco’s Product Support identify your system and its factory configuration in case the SP04-140 or its components require service. A label citing your product’s serial number is attached to the bottom panel of t...
Page 7 - Equipment Placement and Rack Mounting; DESKTOP MOUNTING
C613M-A (5/05) 7 Equipment Placement and Rack Mounting The SP04-140 can be placed on a flat surface, such as a desktop; mounted to a wall; or mounted into an equipment rack. DESKTOP MOUNTING To place the SP04-140 on a flat surface, such as a desktop: 1. Make sure the rubber feet are installed on the...
Page 8 - WALL MOUNTING
8 C613M-A (5/05) WALL MOUNTING The SP04-140 can be mounted to a wall using the optional WM5001-4U wall mount system. You can mount up to four SP04-140, NET5301T, and NET5301R units, in any combination, in a fully expanded WM5001-4U (one WM5001-4U with up to three WM5001-4UEXP expansion units). To mo...
Page 9 - RACK MOUNTING
C613M-A (5/05) 9 RACK MOUNTING Any combination of SP04-140, NET5301T, and NET5301R units can be mounted together in the optional RK5000PS-5U rack mount kit, up to 12 units. Each unit plugs directly into a power connector in the rack and is powered by the rack. NOTE: The RK5000PS-5U only supplies pow...
Page 10 - PELCO BADGE ORIENTATION
10 C613M-A (5/05) PELCO BADGE ORIENTATION The Pelco badge on the front panel of the SP04-140 can be rotated in quarter turns. If you install the unit on a flat surface, the Pelco badge will be turned the wrong way. To rotate the Pelco badge: 1. Use the Pelco badge rotation sticker that came with the...
Page 11 - Connections; CONNECTING VIDEO INPUTS
C613M-A (5/05) 11 Connections Familiarize yourself with the SP04-140 rear panel before connecting any equipment to the unit. Figure 8. SP04-140 Rear Panel CONNECTING VIDEO INPUTS The SP04-140 offers two analog video inputs. The unit automatically detects the video standard (PAL or NTSC) and accepts ...
Page 12 - Maximum Distance
12 C613M-A (5/05) Before installing the SP04-140, make sure the distance from the unit to the video device is less than the maximum distance for the coaxial cable. Refer to Table A for maximum video coaxial cable distances. Table A. Video Coaxial Cable Requirements *Cable requirements: 75-ohm impeda...
Page 13 - CONNECTING AUDIO; Line; Connector Sleeve
C613M-A (5/05) 13 CONNECTING AUDIO The SP04-140 supports half-duplex, bidirectional audio (one direction at a time). It transmits audio and video signals simultaneously. This lets you control a loudspeaker or other audio equipment, such as a door intercom system, at the monitored location. The unit ...
Page 14 - CONNECTING A PTZ DEVICE, RELAY, AND ALARMS
14 C613M-A (5/05) CONNECTING A PTZ DEVICE, RELAY, AND ALARMS The SP04-140 incorporates a 16-pin terminal block to support the following: • PTZ device, such as a dome camera, using the Pelco D protocol (RS-422) • Relay control, either normally open or normally closed • Up to three alarm inputs, super...
Page 15 - CONNECTING A PTZ DEVICE (PELCO D PROTOCOL)
C613M-A (5/05) 15 CONNECTING A PTZ DEVICE (PELCO D PROTOCOL) NOTE: To connect a Coaxitron PTZ device, refer to Connecting Video Inputs The SP04-140 supports camera control using Pelco D protocol (RS-422) for a PTZ device. You can connect only one serial PTZ device to a video encoder. The default Pel...
Page 16 - CONNECTING A RELAY DEVICE; Setting
16 C613M-A (5/05) Refer to Table C when installing the PTZ device. It lists the serial port settings that the SP04-140 supports. Table C. Serial Port Options and Defaults CONNECTING A RELAY DEVICE The SP04-140 has an output for triggering an external device. It supports both momentary and continuous...
Page 17 - CONNECTING ALARMS; Supervised Alarms
C613M-A (5/05) 17 CONNECTING ALARMS The SP04-140 offers three alarm inputs for external signaling devices, such as door contacts or motion detectors. Each encoder supports either all normally open or all normally closed devices. If your installation requires mixed devices, install another SP04-140, ...
Page 18 - Unsupervised Alarms
18 C613M-A (5/05) Figure 15 illustrates the wiring configuration for supervised alarm inputs. Figure 15. Supervised Alarm Input Wiring Unsupervised Alarms When an alarm is configured as an unsupervised alarm, the SP04-140 only triggers an alarm when the normal alarm state (open or closed) changes. F...
Page 19 - Alarm Connections; CONNECTING POWER; Model
C613M-A (5/05) 19 Alarm Connections Figure 18 shows how to wire the video encoder to an alarm (refer to Table B for the specific connector pin assignments). Figure 18. Connecting Alarms CONNECTING POWER The SP04-140 video encoder is designed to operate from either a 12 VDC or a 24 VAC power supply. ...
Page 20 - CONNECTING TO THE NETWORK; Wire Gauge
20 C613M-A (5/05) Use Table E to help identify the necessary wire gauge and maximum cable distance. This table applies to two-conductor solid copper wire. (Reduce distance by 10% for stranded copper wire.) These maximum distances are based on a maximum allowable voltage drop of 10%. Table E. Recomme...
Page 21 - Operation; FRONT PANEL INDICATORS; Unit status; Network status
C613M-A (5/05) 21 Operation Refer to the WS5000 operation manual for details on how to access and configure the SP04-140 video encoder. FRONT PANEL INDICATORS Figure 20. SP04-140 Front Panel Pelco badge (power) The Pelco badge glows blue when the unit has power. Unit status Unit status is indicated ...
Page 22 - CONFIGURATION/RESET BUTTON; Mode
22 C613M-A (5/05) CONFIGURATION/RESET BUTTON Use the recessed configuration/reset button at the top of the front panel to access the following modes: Table F. Configuration/Reset Button Functions and Indicators To access one of these modes: 1. Use a probe or paper clip to press and hold the configur...
Page 23 - Troubleshooting; Problem
C613M-A (5/05) 23 Troubleshooting If the following instructions fail to solve your problem, contact Pelco Product Support at 1-800-289-9100 or 1-559-292-1981 for assistance. Access the properties windows for the SP04-140 video encoder on the WS5050 workstation (refer to the WS5000 operation manual)....
Page 24 - Specifications; MODEL NUMBER
24 C613M-A (5/05) Specifications MODEL NUMBER SP04-140 Dual-input network video server that encodes video, audio, and control data for transmission over an IP network SUPPLIED ACCESSORIES Mating Connectors One 16-pin, one 2-pin SYSTEM Processor PowerPC ® 405EP Operating System Linux ® User Interface...
Page 26 - STANDARDS/ORGANIZATIONS
26 C613M-A (5/05) STANDARDS/ORGANIZATIONS • Pelco is a member of the MPEG-4 Industry Forum • Pelco is a member of the Universal Plug and Play (UPnP) Forum • Pelco is a member of the Universal Serial Bus (USB) Implementers Forum • Pelco is a contributor to the International Standards for Organization...
Page 27 - PRODUCT WARRANTY AND RETURN INFORMATION
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material orworkmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic ...
