Page 2 - CONTENTS; Section
2 Pelco Manual C586M (9/99) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 4 DESCRIPTION ................................................................................................................... 4 MODELS ...............
Page 3 - LIST OF ILLUSTRATIONS; Figure; LIST OF TABLES; Table
Pelco Manual C586M (9/99) 3 LIST OF ILLUSTRATIONS Figure Page 1 Rear Panel of KDB4000V Keyboard .................................................................. 7 2 KBD4000V Interface Mounting Hole Dimensions .............................................. 7 3 Connecting KBD4000V to a Multiplexer ....
Page 4 - IMPORTANT SAFEGUARDS AND WARNINGS; Only use replacement parts recommended by Pelco.; DESCRIPTION
4 Pelco Manual C586M (9/99) IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel andconform to all local codes. 2. Unless the unit is specifically m...
Page 5 - MODELS; INSTALLATION; The following parts are supplied:; Multiplexer Mode Installation; or; Multiplexer Server Mode Installation; MULTIPLEXER MODE INSTALLATION; ADDRESS; Set switch 7 ON if you want to address all cameras consecutively.; control
Pelco Manual C586M (9/99) 5 MODELS KBD4000V Keyboard for pan, tilt and lens control of variable speed receivers.Includes 5-inch (12.7 cm) diagonal color monitor. 120 VAC, 60 Hz. KBD4000V-X Keyboard for pan, tilt, and lens control of variable speed receivers.Includes 5-inch (12.7 cm) diagonal color m...
Page 6 - PROGRAMMING MODE; If the keyboard will; MULTIPLEXER SERVER MODE INSTALLATION; Keyboard Addresses; Keyboard; Video Coaxial Cable Wiring Distances; Maximum Distance; If the distance
6 Pelco Manual C586M (9/99) PROGRAMMING MODE Set switch 8 ON to program the multiplexer and camera presets and patterns from thekeyboard. Set the switch OFF to disable programming. 3. Replace the cover on the back of the keyboard. 4. Peel off the protective coverings over the LED display and the LCD...
Page 7 - Connecting KBD4000V to a Multiplexer
Pelco Manual C586M (9/99) 7 Figure 2. KBD4000V Interface Mounting Hole Dimensions Figure 1. Rear Panel of KDB4000V Keyboard 2 . 5 " ( 6 . 4 c m ) RX+ RX- GND TX- TX+ 1 2 3 4 O N V I D E O P OW E R O N O F F K B D 4 0 0 0 V I N T E R FA C E I N T E R FAC EC A B L E P OW E R S U P P LY K B D 4 0 0...
Page 8 - M U LT I P L E X E R S E RV E R; Connecting KBD4000Vs to a Multiplexer Server
8 Pelco Manual C586M (9/99) P OW E R S U P P LY K B D 4 0 0 0 V I N T E R FA C E P OW E R S U P P LY P OW E R S U P P LY K B D 4 0 0 0 V M U LT I P L E X E R S E RV E R K B D 4 0 0 0 V K B D 4 0 0 0 V R+ R- T- T+ R+ R- T- T+ R+ R- T- T+ R+ R- T- T+ R+ R- T- T+ R+ R- T- T+ LOCAL KEYBOARD MUX(S) VIDEO...
Page 9 - INTERFACE; MULTIPLEXER SERVER; Connecting KBD4000 Series Keyboards to a Multiplexer Server
Pelco Manual C586M (9/99) 9 POWER SUPPLY TO KBD4000V FROM MULTIPLEXERSERVER R+ R- T- T+ LOCAL FIRST KBD WALL BLOCK TERMINAL 1 2 3 4 5 6 7 8 SECOND KBD WALL BLOCK TERMINAL 1 2 3 4 5 6 7 8 12 VAC WALL TRANSFORMER USER- SUPPLIED CABLE 1 2 3 4 5 6 7 8 WALL BLOCK TERMINALS TX+ TX- GND RX- RX+ 12 VAC WALL...
Page 11 - OPERATION; IMPORTANT NOTE ABOUT PROGRAMMING; Programming; IMPORTANT NOTE ABOUT COAXITRON; Camera Setup
Pelco Manual C586M (9/99) 11 OPERATION IMPORTANT NOTE ABOUT PROGRAMMING When the keyboard is plugged into a multiplexer or multiplexer server, the keyboard isready to operate. However, some minimal programming may be required to make your system work. MULTIPLEXER The default settings for the duplex ...
Page 12 - simplex; The; duplex; multiplexer has two modes of operation: live and VCR.
12 Pelco Manual C586M (9/99) IMPORTANT NOTE ABOUT DIFFERENCES IN SIMPLEX ANDDUPLEX MULTIPLEXER MODES OF OPERATION The simplex multiplexer has three modes of operation: live, VCR, and record. • In the live mode, the main monitor can show live video both in full-screen ormultiple-screen views. You can...
Page 13 - KBD4000V Keyboard Definitions
Pelco Manual C586M (9/99) 13 1. LED DISPLAY Displays the address of the multiplexer (from 1-16) with which the keyboard is communicating. 2. LIVE/VCR KEY Selects the source of video to display on the monitor(s). LIVE is live video from the cameras.VCR is recorded video that is played back from a VCR...
Page 14 - Operation Guide
14 Pelco Manual C586M (9/99) Table C. Operation Guide NOTE: References to switch 7 in this table refer to the switch behind the panel on the back of the keyboard. There are two modes for addressing cameras: by addressing all the cameras consecutively from 1-256 (switch 7 ON, refer to Table D) or bya...
Page 21 - Camera Numbers with Switch 7 ON; Multiplexer
Pelco Manual C586M (9/99) 21 OPERATION KEYBOARD COMMAND RESULT Table C. Operation Guide (Continued) 1. Press the MAIN MONITOR key. The green LED over the MAIN key lights. 2. On the number pad, press the address number of the multiplexer (1-16 if the keyboard is connected to amultiplexer; 1-8 if the ...
Page 22 - PROGRAMMING; IMPORTANT NOTE; Use the arrow buttons to move the cursor to UNIT ID.; PASSWORD; Advanced; Whenever a
22 Pelco Manual C586M (9/99) PROGRAMMING This section applies only to programming the multiplexer. To program themultiplexer server, refer to the server manual. Programming allows you to configure the multiplexer from the KBD4000V for the way thatyou want your system to operate. The multiplexer auto...
Page 23 - MENUS; To program the main basic system parameters:; Time and Date; Set the current time and date. The time uses a 24-hour clock.; Time Display; Once you are in a
Pelco Manual C586M (9/99) 23 MENUS To program from the keyboard, the keyboard must be in main monitor mode. Press theMAIN MONITOR key. SYSTEM SETUP (View Key) To program the main basic system parameters: 1. Press the MAIN MONITOR key. 2. Use the number keypad to enter the address of the multiplexer ...
Page 25 - Date Format; Sets the format for displaying the date on the main monitor.; Password; Advanced System Setup Menu
Pelco Manual C586M (9/99) 25 3. Press the VIEW key for approximately three seconds. The basic System Setup menuappears (refer to Figure 8). 4. The currently selected menu item blinks. Use the joystick to highlight ADVANCEDSETUP. 5. Press the OPEN key. The Advanced System Setup menu appears (refer to...
Page 26 - When; Troubleshooting
26 Pelco Manual C586M (9/99) SEQUENCE - Allows you to view an individual camera or run a sequence. An alarm oractivity detection will override what you are observing. When the alarm or activitydetection goes away, the screen will return to the camera or sequence you wereviewing. TRACK MAIN - The spo...
Page 28 - NTSC; UNIVERSAL
28 Pelco Manual C586M (9/99) Figure 10. Basic VCR Setting Menu Table E. VCR Types NTSC PAL UNIVERSAL UNIVERSAL GYYR TLC1800 ASUTA TLVCR 251 GYYR 2100 ASUTSA TLVCR 964 GYYR 2100 HD MODE BURLE TC3910X JVC SR-L900U HITACHI VTL30E JVC SR-L901U HITACHI VT-L1000E JVC SR-9070U HITACHI VT-L2000E JVC BR-S925...
Page 29 - Record Speeds; For proper
Pelco Manual C586M (9/99) 29 CUSTOM VCR SETUP (Live/VCR Key) To program the advanced VCR parameters: 1. Press the MAIN MONITOR key. 2. Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard isconnected to a multiplexer; 1-8 if the keyboard is connected to a server), then...
Page 30 - Video Termination; Basic Camera Menu
30 Pelco Manual C586M (9/99) CAMERA SETUP (Number and CAM Keys) To program a camera input: 1. Press the MAIN MONITOR key. 2. Select the camera. Addressing by Multiplexer (Switch 7 OFF) a. On the number keypad, enter the address number of the multiplexer (1-16 if thekeyboard is connected to a multipl...
Page 31 - Coaxitron Format; OFF - Use when your system has fixed cameras only.; Activity Detection; When you have completed all the changes you want to make, go to EXIT.; The Coaxitron
Pelco Manual C586M (9/99) 31 Coaxitron Format EXTENDED - Use when your system has moveable cameras controlled by 32-bitCoaxitron receivers, such as Esprit, Intercept, Spectra, and LRD41C21/LRD41C22 Series. OFF - Use when your system has fixed cameras only. STANDARD - Use when your system has moveabl...
Page 32 - ACTIVITY DETECTION MASK SETUP; To program an activity detection mask for a camera:; Activity Detection Mask
32 Pelco Manual C586M (9/99) ACTIVITY DETECTION MASK SETUP Activity detection continually monitors selected camera inputs for motion. When motion isdetected, the multiplexer increases the frequency with which that camera(s) is shown andrecorded. Activity detection is most effective when only a few c...
Page 34 - HELP MENU; The Help menu is accessed from any other menu.; Camera Sequence Menu
34 Pelco Manual C586M (9/99) HELP MENU The Help menu is accessed from any other menu. 1. Use the joystick in any menu to highlight HELP. 2. Press the OPEN key. The Help menu appears. Figure 14. Camera Sequence Menu Figure 15. Help Menu GROUP QUAD (2x2) 1 04 2 04 3 04 4 04 NINE (3x3) 04 04 VCR/LIVE *...
Page 35 - MULTIPLE CAMERA DISPLAY SETUP
Pelco Manual C586M (9/99) 35 MULTIPLE CAMERA DISPLAY SETUP The multiple camera display formats may be configured using the keyboard. The LEDsabove the camera buttons on the multiplexer will illuminate to indicate which cameras arebeing displayed. PROGRAMMING THE PICTURE-IN-PICTURE DISPLAY( Key) The ...
Page 37 - PROGRAMMING MENU DEFAULTS; Programming Menu Defaults; Menu
Pelco Manual C586M (9/99) 37 PROGRAMMING MENU DEFAULTS Table F. Programming Menu Defaults Menu Item Default System Setup Time Display On Title Display On Normal Record Speed 2/6/8 Hr (NTSC/EIA)3 Hr (PAL/CCIR) Alarm Record Speed 2/6/8 Hr (NTSC/EIA)3 Hr (PAL/CCIR) Main Monitor Video (Duplex Only) Comp...
Page 38 - PROGRAMMING A PRESET; set to TRACK MAIN (refer to the; PROGRAMMING A PATTERN; set to TRACK MAIN (refer to the; Advanced System Setup; Move the camera through the pattern.; The LEDs above
38 Pelco Manual C586M (9/99) PROGRAMMING A PRESET 1. Press the MAIN or SPOT MONITOR key. The green LED over the MAIN or SPOT keylights. When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item inthe Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup secti...
Page 39 - TROUBLESHOOTING
Pelco Manual C586M (9/99) 39 TROUBLESHOOTING If you have difficulty operating your system, run through the following checklist to see if youcan solve the problem. 1. Are the keyboard switches set properly? 2. Is the equipment wired properly? 3. Are the menu options in the multiplexer(s) and server s...
Page 40 - OR; immediately
40 Pelco Manual C586M (9/99) 17. If you have a server and cannot change between full screen and multiple screen views on the main monitor, check the MAIN MONITOR CONTROL setting in the Monitormenu of the server. 18. If the UNIT ID, in the ADVANCED SYSTEM SETUP menu, is inadvertently changed at the k...
Page 41 - SPECIFICATIONS; ELECTRICAL
Pelco Manual C586M (9/99) 41 SPECIFICATIONS ELECTRICAL Input Voltage: +12 VDC @ 1A Power Consumption: 8 watts Joystick: Three-axis, vector solving, with twisting, return-to-center head Data Interface: RS-485, 25-foot (7.6 m) cable supplied Data Connector Type: RJ-45, 8-pin modular (female) Digital D...
Page 42 - REVISION HISTORY; Date; PRODUCT WARRANTY AND RETURN INFORMATION
42 Pelco Manual C586M (9/99) REVISION HISTORY Manual # Date Comments C586M 9/99 Original version. Pelco, the Pelco Logo, Camclosure, Esprit, Genex, Intercept, Legacy, and Spectra are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved.Endura and ExSite are trademarks of Pelc...
