Pelco C491M-D - Manual
Pelco C491M-D – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Mount the camera and lens to the tilt table.; MAINTENANCE; window with a mild non-abrasive detergent in; SPECIFICATIONS; MECHANICAL; Camera Mounting: Adjustable tilt table; ELECTRICAL
- Page 3 – GENERAL; Gray polyester powder coat; Figure 1. HS4100BH Dimension Drawing; NOTE: VALUES IN PARENTHESES ARE CENTIMETERS
- Page 4 – ® Pelco and the Pelco logo are registered trademarks of Pelco.; WARRANTY AND RETURN INFORMATION; REVISION HISTORY; Date
300 W. Pontiac Way,
Clovis, CA 93612-5699
USA
In North America & Canada:
Tel (800) 289-9100
FAX (800) 289-9150
DataFAX (800) 289-9108
International Customers:
Tel (1-559) 292-1981
FAX (1-559) 348-1120
DataFAX (1-559) 292-0435
Pelco Online
http://www.pelco.com
®
C491M-D (3/99)
HS4100BH
High-Security Camera Enclosure
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1.
Installation and servicing should only be done by qualified service personnel and conform
to all local codes.
2.
Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclo-
sure, it is designed for indoor use only and it must not be installed where exposed to rain
and moisture.
3.
Only use replacement par ts recommended by Pelco.
4.
The installation method and materials should be capable to suppor ting four times the
weight of the enclosure, pan/tilt, camera and lens combination.
5.
The camera and lens combination shall not exceed 20 pounds (9.06 kg).
The product and/or manual may bear the following marks:
C A U T I O N :
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
This symbol indicates that danger-
ous voltage constituting a risk of
electric shock is present within this
unit.
This symbol indicates that there are
important operating and mainte-
nance instructions in the literature
accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.
DESCRIPTION
The HS4100BH is a high-security camera enclosure designed to be mounted in indoor walls in
applications requiring maximum protection from vandalism, such as prisons and detention
cells.
There is no exposed mounting hardware holding the enclosure to its mounting surface be-
cause the HS4100BH replaces a half-size concrete block during construction of the wall. The
HS4100BH is made of heavy-gauge steel and is equipped with a window of 1/2-inch (1.27 cm)
thick, impact-resistant Lexan
®
.
The HS4100BH accepts most CCD cameras with fixed focal length lenses and some motor-
ized zoom lenses. Access to the inside is through the front or rear with a specially designed
tool, so the enclosure cannot be opened by unauthorized people. In addition, a factor y-in-
stalled tamper switch is mounted on the secured access cover.
INSTALLATION
The following parts are supplied:
1
Enclosure
1
Tampruf #10 socket, 1/4-inch drive
The HS4100BH is designed to be installed in a concrete block wall during construction. The
enclosure’s dimensions allow it to replace a half-size block.
Before installing the HS4100BH enclosure in a wall, make cer tain the wall detail and construc-
tion can support the full weight of the enclosure plus the camera and lens. The HS4100BH
must not be considered a structural component in a wall. Make sure during construction that
the access panels are not obstructed by mortar.
L I S T E D
UL
®
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
After incorporating the enclosure into the wall structure, follow the steps below to complete theinstallation. 1. Remove the appropriate knock-outs and route the required cables to the enclosure. 2. You can access the inside of the enclosure from either the front or rear. Use the suppliedTampruf #10...
GENERAL Construction: Seam-welded 10-gauge (0.134 in. or 0.34 cm) steel Finish: Gray polyester powder coat Dimensions: See Figure 1 Environment: Indoor; 32 ° to 120 ° F (0 ° to 49 ° C) Weight: Unit Shipping 23 lb (10.35 kg) 27 lb (12.23 kg) Rating: NEMA 1IP 20 (Design and product specifications subj...
® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved. WARRANTYPelco will repair or replace, without charge, any merchandise proved defec-tive in material or workmanship for a period of one year after the date ofshipment. Exceptions to this warra...
