Pelco C3453M-B - Manual - manualsarea.com

Page 3 - Important Safety Instructions

C3453M-B (4/09) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the ma...

Page 4 - Description; MODELS

4 C3453M-B (4/09) Description The EH1512 Series indoor/outdoor enclosures are designed for use with small- to medium-sized analog and IP cameras. They will accommodate both fixed and variable focal length lenses (with or without auto-iris operation). They can be wall mounted using either Pelco’s EM1...

Page 5 - PACKAGE CONTENTS; Qty Description

C3453M-B (4/09) 5 PACKAGE CONTENTS NOTE: A metric Allen wrench (5 mm) is required for installation but is not included. A Phillips screwdriver, flat head screwdriver, or 1/4-inch nut driver is needed for the EH1512-1 and EH1512-3 only. The Allen wrench is needed to open and close the enclosure and t...

Page 6 - Installation; INSTALLING THE CAMERA AND MOUNT

6 C3453M-B (4/09) Installation INSTALLING THE CAMERA AND MOUNT To install the enclosure, camera, and lens: 1. Use a 5-mm Allen wrench (not supplied) to loosen the three screws on the enclosure base. 2. Lift up and remove the lid (refer to Figure 2). Hang the lid from the front of the enclosure base ...

Page 7 - Wiring the enclosure with the cable not in conduit

C3453M-B (4/09) 7 3. Remove the camera sled from the enclosure rail (refer to Figure 3). a. Squeeze the two plastic tabs (located near the front window) that hold the camera sled in place. b. Pull up and slide the sled forward. c. Remove the sled. Figure 3. Removing the S led 4. Remove the parts bag...

Page 10 - INSTALLING THE SUN SHROUD

10 C3453M-B (4/09) INSTALLING THE SUN SHROUD The optional sun shroud fits over the top of the EH1512 enclosure. Perform the following steps to install the sun shroud. 1. Position the front of the sun shroud above the front of the enclosure. 2. Press the sun shroud down and against the enclosure unti...

Page 11 - Maintenance; Wire Gauge; Maximum Distance

C3453M-B (4/09) 11 Table C describes the recommended maximum distances for 24 VAC applications, which are calculated with a 10 percent voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC-powered devices.) For example, an enclosure that requires 30 VA and is installed 94...

Page 12 - Specifications; Model Number

12 C3453M-B (4/09) Specifications MODELS *Enclosure power consumption does not include camera wattage. MECHANICAL Camera Mounting Single slot for adjustable camera positioning on snap-in camera sled Camera and Lens Size Accepts camera and lens combinations † (including BNC connector) up to 9.00"...

Page 14 - RECOMMENDED CAMERAS AND LENSES

14 C3453M-B (4/09) RECOMMENDED CAMERAS AND LENSES Cameras C10CH-6, C10CH-6X, C10CH-7X, C10DN-6, C10DN-6X, C10DN-7X, CCC1390H-6, CCC1390H-6X, IP3701H-2, IP3701H-2X, IXS0C, IXS0DN, IX10C, IX10DN, IXE20C, IXE20DN, IX30C, IX30DN Lenses 13VD2.8-12, 13VD3-8, 13VD5-40, 13VD5-50, 13VDIR2.8-11, 13VDIR3-8.5, ...

Page 15 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years: – Fiber optic products– TW3000...

Pelco C3453M-B - Manual

Table of Contents:

Summary

Other Pelco Models