Page 3 - Contents
C2924M (4/05) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Warnings . . . . . . . . . . . . . . . . . . . . . . ....
Page 6 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE; Warnings
6 C2924M (4/05) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired ...
Page 7 - Description; PRODUCT FEATURES
C2924M (4/05) 7 Description The CCC1390H Series camera is a compact, wide dynamic range (WDR), day/night camera. Its WDR technology provides up to 60 dB of dynamic range and produces superior images over a wide range of lighting conditions, including extreme backlight conditions. The camera also use...
Page 8 - MODELS
8 C2924M (4/05) Figure 1. CCC1390H Series Camera MODELS CCC1390H-6 1/3-inch high resolution day/night, WDR, CCD camera, 24 VAC or 12 VDC, NTSC format CCC1390H-6X 1/3-inch high resolution day/night, WDR, CCD camera, 24 VAC or 12 VDC, PAL format 3 3a Lens Mount: Mount a standard CS-mount lens to the C...
Page 10 - Lens Mounting; WIRING AN AUTO IRIS LENS; Pin
10 C2924M (4/05) Lens Mounting The CCC1390H Series camera supports both manual and DC-drive auto iris lenses, either fixed focal length or varifocal. It automatically senses an auto iris lens as soon as you plug in the connector. The camera has a standard CS-mount that can accept a C-mount lens with...
Page 11 - MOUNTING THE LENS
C2924M (4/05) 11 MOUNTING THE LENS To mount the lens onto the camera (refer to Figure 3): 1. Make sure the lens will not touch the camera imager when installed. 2. Use clean, compressed air or a clean, dry lens cloth to make sure there is no dust or other foreign matter between the lens and the came...
Page 12 - Camera Mounting
12 C2924M (4/05) Camera Mounting The CCC1390H Series camera can be mounted from either the top or bottom, depending on the type of camera mount used in your installation. Use a standard 1/4-20 screw. The maximum thread depth (top) is 0.188 inches (4.7 mm). To extend the thread depth (top) to 0.25 in...
Page 13 - CONNECTING POWER; Wire Gauge
C2924M (4/05) 13 Connecting Power, Video, and Control The CCC1390H Series camera offers standard power and coax video connectors as well as an external control connector. Before installation, identify how you will connect each power, video, and control lead to the camera. CONNECTING POWER The CCC139...
Page 14 - CONNECTING AC POWER
14 C2924M (4/05) CONNECTING AC POWER The CCC1390H Series camera requires a power supply of 24 VAC ±15% (20.4 to 27.6 VAC), 50/60Hz. Make sure the power supply has a minimum rating of 270 mA. When connecting more than one camera to the same AC transformer, remember the following: • Connect the same s...
Page 15 - CONNECTING DC POWER; CONNECTING VIDEO; Maximum Distance
C2924M (4/05) 15 CONNECTING DC POWER The CCC1390H Series camera requires a power supply of 12 VDC ±15% (10.2 to 13.8 VDC). Make sure the power supply has a minimum rating of 390 mA. To connect DC power: 1. Strip at least 0.4 inches (10 mm) of the insulation from each power wire. 2. Press and hold th...
Page 16 - CONNECTING EXTERNAL CONTROL
16 C2924M (4/05) CONNECTING EXTERNAL CONTROL The external control connector on the rear panel lets you remotely access and control the CCC1390H Series camera. The external control connector assembly is a seven-pin micro (1.25 mm) connector with wires (26 AWG) and connector cover. You can access and ...
Page 17 - Shielded cable
C2924M (4/05) 17 CONNECTING SERIAL CONTROL (PELCO D/PELCO P) To connect serial control to the camera (refer to Figure 7): 1. Turn off power to the camera. 2. If necessary, use a small Phillips screwdriver to remove the connector cover from the rear panel (refer to Figure 6). 3. If necessary, plug th...
Page 18 - CONNECTING DAY/NIGHT FILTER CONTROL
18 C2924M (4/05) 7. If you are not connecting additional cameras, or after adding all cameras to the chain, make sure you set the termination switch to ON for the last camera in the chain. 8. Access the CAMERA SETUP menu to set the following (refer to Camera Setup): • Set a unique ADDRESS for each c...
Page 19 - Shielded cable only:
C2924M (4/05) 19 4. Use 100-ohm twisted pair cabling to wire the device to the enclosed connector assembly. The decision to use shielded cable depends on your installation; shielded cable may be optional. Figure 8. Day/Night Filter Control Configuration 5. Wire the camera to the external switch as f...
Page 20 - Quick Setup; SENS; WD
20 C2924M (4/05) Quick Setup Several CCC1390H Series camera settings can be changed directly from the rear panel button. When a rear panel indicator is lit, the correspond-ing option is enabled. You can change the following options directly from the rear panel: AGC Press the button up to enable or d...
Page 21 - Accessing Setup Menus; NAVIGATING SETUP MENUS FROM THE REAR PANEL; MENU ACTION
C2924M (4/05) 21 Accessing Setup Menus NAVIGATING SETUP MENUS FROM THE REAR PANEL You can use the five-position button on the rear panel to access and navigate the setup menus (refer to Figure 10). Figure 10. Rear Panel Indicators and Presses Table E lists the button presses for each menu action. To...
Page 22 - NAVIGATING SETUP MENUS FROM A PELCO CONTROLLER; USING PRESET 95 TO ACCESS SETUP MENUS
22 C2924M (4/05) NAVIGATING SETUP MENUS FROM A PELCO CONTROLLER USING PRESET 95 TO ACCESS SETUP MENUS You can use preset 95 to access and navigate the setup menus from various Pelco controllers. Use the instructions for your controller to access the main menu. CM6700/CM6800 1. Enter the camera numbe...
Page 23 - NAVIGATING SETUP MENUS
C2924M (4/05) 23 NAVIGATING SETUP MENUS As soon as you access the MAIN MENU, the four indicators on the rear panel blink until you close the setup menu. Table F lists the buttons and actions for menu navigation. NOTE: If your Pelco controller does not have a joystick, use the up, down, right, and le...
Page 24 - Setup Menus
24 C2924M (4/05) Setup Menus The CCC1390H Series camera uses setup menus instead of hardware switches for configuring the camera. As a result, you have more options for customizing the camera for its specific application. NOTES: • After you customize any aspect of the CCC1390H Series camera, be sure...
Page 26 - ACTIVE; STANDARD
26 C2924M (4/05) MAIN MENU The following sections describe each menu and all settings associated with that menu. The sample screens in each section show the default settings. To display the MAIN MENU: • Press and hold the center of the button on the rear panel. Refer to Navigating Setup Menus from t...
Page 27 - SAVE AS
C2924M (4/05) 27 Table G shows the default camera settings for each profile. Figure 11 shows sample scenes for each camera profile. Figure 11. Sample Profile Scenes SAVE AS Use this option to save all settings from the <HOLD> profile into the CUSTOM profile. After selecting this option, the AC...
Page 28 - EXPOSURE SETTINGS; NORMAL; WDR; VIDEO LEVEL; FLICKERLESS
28 C2924M (4/05) EXPOSURE SETTINGS Select this option to configure the exposure settings for the CCC1390H Series camera. The default EXPOSURE SETTINGS menu appears when AUTO EXPOSURE is set to NORMAL, BLC, or WDR. When AUTO EXPOSURE is set to MANUAL, the FLICKERLESS option is replaced with the SHUTT...
Page 29 - SHUTTER SPEED; DAY AND NIGHT; AUTO; COLOR
C2924M (4/05) 29 SHUTTER SPEED Use this option to set the shutter speed manually. Select one of the following options: 1/60(NTSC), 1/50(PAL), 1/100(NTSC), 1/120(PAL), 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/20000, 1/50000. The default is 1/60(NTSC) or 1/50(PAL). NOTE: This option appears wh...
Page 30 - OFF
30 C2924M (4/05) DAY AND NIGHT DETECTION The camera regularly checks the brightness level. When the brightness level crosses the switch threshold and lasts longer than the D&N DETECTION setting, the camera switches the filter. For example, the headlights of a passing car affect the brightness le...
Page 31 - FUNCTION SETTINGS; LINE SYNCHRONIZATION; Line Sync; WHITE BALANCE
C2924M (4/05) 31 FUNCTION SETTINGS Select this option to configure the function settings for the CCC1390H Series camera. LINE SYNCHRONIZATION Use line synchronization to eliminate the vertical roll that occurs when multiple cameras are connected to the same switching device. Line synchronization loc...
Page 32 - GAMMA
32 C2924M (4/05) MANUAL RED/BLUE Select this option to display the MANUAL RED/BLUE menu. Red Gain Use this option to either increase or decrease the light level of the red elements in the camera image. Select a value between -5 and 5. The default is -1. Blue Gain Use this option to either increase o...
Page 33 - MASKING; Mask; TITLE; Title
C2924M (4/05) 33 MASKING Masking lets you block out certain areas of a camera scene. Select this option to configure one to eight masks in the camera image. NOTE: When you enable masking, electronic zoom is disabled. If electronic zoom is active, masking is disabled. Mask Use this option to enable o...
Page 34 - CAMERA SETUP; Address; AUTO IRIS LENS ADJUSTMENT
34 C2924M (4/05) 5. To clear a character, select BS (backspace). The camera deletes the last character entered. 6. Repeat steps 3 and 4 until you have entered the camera title. 7. When the title is correct, select BACK to return to the TITLE menu. CAMERA SETUP Select this option to configure the ser...
Page 35 - Restore Factory Settings
C2924M (4/05) 35 PIXEL CORRECTION If white spots appear in the video image, one or more pixels on the camera imager may be defective. This condition is common to CCD camera imagers. Select this option to automatically detect and correct these defects. This feature helps you maintain image quality. T...
Page 36 - Lens Focusing; Fixed focal length lens only:
36 C2924M (4/05) Lens Focusing After mounting the lens, you must focus your CCC1390H Series camera. You will adjust both the back focus (on the camera) and the fine focus (on the lens). NOTE: The back focus has already been adjusted using a standard CS-mount lens. However, you might need to adjust i...
Page 37 - Varifocal lens only:
C2924M (4/05) 37 6. Varifocal lens only: a. Set the varifocal to wide (W) and the lens focal length to far ( ∞ ). b. Adjust the back focus: (1) Use the enclosed 1.5-mm Allen wrench to loosen the back focus locking screw. (2) Turn the lens until the image is focused. (3) Tighten the back focus lockin...
Page 40 - Specifications; GENERAL
40 C2924M (4/05) Specifications GENERAL Day/Night Operation Day Infrared (IR) cut filter Night BK-7 glass, same optical displacement as day Imaging Device 1/3-inch image format Sony SS-2WD CCD Dynamic Range 60 dB maximum (WDR mode) Picture Elements NTSC 768 (H) x 494 (V) (approx. 380K) PAL 752 (H) x...
Page 43 - PRODUCT WARRANTY AND RETURN INFORMATION
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material orworkmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic ...
