Pelco C283M-C - Manual
Pelco C283M-C – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – OPTIONAL RECEIVER MODELS; INSTALLATION
- Page 3 – (Design and specifications are subject to change without notice.); LWM41 Dimension Drawing
- Page 4 – PRODUCT WARRANTY AND RETURN INFORMATION; REVISION HISTORY; Worldwide Headquarters
C283M-C (4/07)
LWM41
Legacy
®
Wall Mount
IMPORTANT SAFETY INSTRUCTIONS
1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.
3. Use only installation methods and materials capable of supporting four times the maximum specified load.
4. Use stainless steel hardware to fasten the mount to outdoor surfaces.
5. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount and
mounting surface.
The product and/or manual may bear the following marks:
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
DESCRIPTION
The LWM41 wall mount is designed for use with all Legacy
®
Series pan/tilts, giving your installation a very neat and attractive look. All Legacy Series
mounts and optional adapters are finished in a textured gray polyester powder coat to match the pan/tilts and enclosures.
The LWM41 wall mount may be directly attached to any vertical load-bearing structure, and can be used with the PA402 pole mount adapter, the CM400
corner mount adapter, or the PP300L/PP301L/PP4348/PP400 adapter for parapet mounting applications. This mount will support up to 150 pounds (68 kg).
The LWM41 may also be used with an optional integral receiver (refer to
Optional Receiver Models
OPTIONAL ADAPTERS
PP300L
Parapet corner adapter mount for LWM41, mounts on rooftops and parapets, rotates 360 degrees, supports 175-pound (79.38 kg) load
PP301L
Parapet corner adapter mount for LWM41, mounts to the inside of parapets, rotates 360 degrees, supports 175-pound (79.38 kg) load
PA402
Pole mount adapter for the LWM41, minimum pole diameter 3 inches (7.62 cm), mounting straps not supplied
PP400
Parapet mount adapter, maximum parapet width 16 inches (40.64 cm)
PP4348
Parapet mount for use with LWM41, mounts to rooftop or horizontal flat surface, supports 75-pound (34 kg) load
CM400
Corner mount adapter, supports up to 150 pounds (68 kg)
OPTIONAL ACCESSORIES
LK4500
Optional lock kit for LWM41 wall mount arm access panel
WARNING:
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
OPTIONAL RECEIVER MODELS LRD41A11-1 Fixed speed, Coaxitron ® compatible only; 120 VAC input voltage; 120 VAC pan/tilt voltage LRD41A11-2 Fixed speed, Coaxitron compatible only; 24 VAC input voltage; 24 VAC pan/tilt voltage LRD41A11-3 Fixed speed, Coaxitron compatible only; 230 VAC input voltage; 120...
To install any Legacy Series pan/tilt with the LWM41 mount: 1. Route the pan/tilt pigtail wire connector through the hole of the mount. 2. Place the pan/tilt on the mount, without the enclosure being attached to the pan/tilt. Be sure the factory-installed gasket is on the bottom of the pan/ tilt spi...
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material orworkmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic p...
