Pelco C1988M-B - Manual - manualsarea.com

Page 2 - REGULATORY NOTICES; Reorient or relocate the receiving antenna.; DESCRIPTION; Models; IMPORTANT SAFEGUARDS AND WARNINGS

[ 2 ] Pelco Manual C1988M-B (4/03) Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should be done only by qualified service and installation personnel. 2. Installation shall be done in accordance with all local and national elec...

Page 3 - Lens Mounting; Back Focus Adjustment; PIN

Pelco Manual C1988M-B (4/03) [ 3 ] CAMERA LAYOUT Figure 1. Camera Layout INSTALLATION Lens Mounting The camera can use a fixed iris, manual iris, or auto iris lens. The camera is factory set for a CS-mountlens, but is easily adjusted for a C-mount lens. 1. C-Mount Lens Only - Rotate the back focus a...

Page 4 - Specifications

[ 4 ] Pelco Manual C1988M-B (4/03) Figure 4. Power Supply Connections Camera Mounting Use a standard 1/4-20 screw (provided) with a maximum thread length of 3/8-inch (10 mm) for top or bot-tom camera mounting. The mount adapter may be fitted to the top or bottom of the camera. The camerais shipped w...

Page 6 - LENS SETUP AND FOCUS PROCEDURES; Video Drive Auto Iris Lens; Fixed Lens; Manual Iris Lens; Zoom Lens

[ 6 ] Pelco Manual C1988M-B (4/03) LENS SETUP AND FOCUS PROCEDURES Video Drive Auto Iris Lens Set the lens mode selector switch to AIV. Switch the ESC OFF. Refer to the lens instructions and adjust thelens for the optimum picture (video output level of 1V peak-to-peak). To focus, fully open the iris...

Page 7 - BACK FOCUS ADJUSTMENT; To adjust the back focus:

Pelco Manual C1988M-B (4/03) [ 7 ] Figure 5. Back Focus Adjustment BACK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of thecase. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. Turn th...

Page 8 - SWITCH SETTINGS; BLC

[ 8 ] Pelco Manual C1988M-B (4/03) SWITCH SETTINGS Figure 6. DIP Switch Default Settings OFFOFF OFF AW1 AIV INT NOR OFF OFF OFF BLC OPT ESC AW2 AID LL SHPLC DS1 DS2 ON PHASE LEVEL + - H L 1 2 3 4 5 6 7 8 9 10 00152 BLC - Backlight Compensation OFF (Default setting) - Disables the BLC mode. BLC - Ena...

Page 9 - White represents switch postion.; LC; Long Line Compensation; DS1 and; - Digital Slow Shutter

Pelco Manual C1988M-B (4/03) [ 9 ] OFF - Disables the DSS mode. 4 Fields of Integration Maximum - 1/15-second scene update rate. 16 Fields of Integration Maximum - 1/4-second scene update rate. 30 Fields of Integration Maximum (Default setting) - 1/2-second scene update rate. NOTE: White represents ...

Page 10 - CAMERA SYNCHRONIZATION (AC OPERATION ONLY); To synchronize the cameras do the following:

[ 10 ] Pelco Manual C1988M-B (4/03) CAMERA SYNCHRONIZATION (AC OPERATION ONLY) When using more than one camera power supply, a brief vertical roll may occur on the monitor when acamera view is switched. To eliminate vertical roll, adjust the phase control by synchronizing, or line-lock-ing, the came...

Page 11 - SPECIFICATIONS; GENERAL

Pelco Manual C1988M-B (4/03) [ 11 ] SPECIFICATIONS GENERAL CCD Sensor: 1/3-inch interline transfer Picture Elements: 768 (H) x 494 (V) Sensing Area: 6 mm diagonally Synchronization System: INT/AC line lock Horizontal Resolution: 480 TV lines Iris Control: Electronic/passive Minimum Illumination: 0.0...

Page 12 - WARRANTY AND RETURN INFORMATION

[ 12 ] Pelco Manual C1988M-B (4/03) REVISION HISTORY Manual # Date Comments C1988M 5/02 Original version. C1988M-A 6/02 Revised the lens connector wiring chart. C1988M-B 4/03 Added S-mark certification. WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any mercha...

Pelco C1988M-B - Manual

Table of Contents:

Summary

Other Pelco Models