Pelco C1302M-F (11/08) - Manual

Page 4 - Important Safety Instructions; RISK OF ELECTRIC SHOCK.

4 C1302M-F (11/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. To reduce the risk of ignition of hazard...

Page 5 - Getting Started; METHODS OF INSTALLATION

C1302M-F (11/08) 5 Getting Started Thank you for purchasing Pelco’s ExSite ® Series explosionproof integrated positioning system. This manual includes instructions for installing all the components of the ExSite Series system. Once the system installation is complete, refer to the operation/programm...

Page 6 - Install the Power Module

6 C1302M-F (11/08) Install the Power Module Attach the power module to the mounting surface. Use only installation methods and materials capable of supporting four times the maximum specified load of the system (220 lb/100 kg). NOTE: If required, install the optional TXB translator, fiber module, or...

Page 7 - CONNECT WIRING; Configuration of Wire Harness

C1302M-F (11/08) 7 CONNECT WIRING Refer to the following information to connect the wires and cables as required. NOTES: • Relay 3 is allocated specifically for an external washer (not supplied by Pelco). • All relays are specified for 32 VDC, 0.5 A. • Wiring/cable for UTP and fiber optic are not pr...

Page 8 - DIP SWITCH SETTINGS; PROTOCOL SETTINGS; Switch Settings for SW3; Switch Number

8 C1302M-F (11/08) DIP SWITCH SETTINGS Configure the receiver address, termination, and baud setting for the system. The DIP switches to configure these settings are located on the top of the power module. NOTE: No DIP switch settings are required for Coaxitron control. Figure 3 shows the default se...

Page 13 - Install the Camera Module

C1302M-F (11/08) 13 Install the Camera Module To install the camera module do the following: 1. Refer to Figure 4. Loosen the set screw at the back of the enclosure with the provided 1.5 mm Allen wrench. Figure 4. Loosen Set Screw 2. Use the supplied spanner wrench to loosen the back of the camera e...

Page 16 - Install the Pan and Tilt Unit

16 C1302M-F (11/08) Install the Pan and Tilt Unit 1. Check for proper seating of the power module seal. Make sure the seal is fully seated in the groove on the top of the power module. Figure 9. Factory-Installed Power Module Seal 2. Refer to Figure 10 and attach the pan and tilt unit to the power m...

Page 18 - Maintenance; CAMERA MODULE REPLACEMENT

18 C1302M-F (11/08) Maintenance CAMERA MODULE REPLACEMENT To replace the camera module do the following: 1. Remove the back cap of the camera enclosure. Refer to Figure 12 and do the following: a. Loosen the set screw with a 1.5 mm Allen wrench. b. Use the supplied spanner wrench to loosen the back ...

Page 21 - Specifications; ELECTRICAL

C1302M-F (11/08) 21 Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 VAC Input Voltage Range ±10% Power Consumption Maximum 60 W (120 VA) per system Electrical Connections 6-foot wire harness with connections for power, video, data control, alarm inputs, and auxiliary outputs MECHANICAL Cab...

Page 23 - PRODUCT WARRANTY AND RETURN INFORMATION

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disp...

Pelco C1302M-F (11/08) - Manual

Table of Contents:

Summary

Other Pelco Models