Page 3 - Contents
C1301M (6/05) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5 - Regulatory Notices
C1301M (6/05) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired ...
Page 6 - Welcome; MODELS
6 C1301M (6/05) Welcome Thank you for purchasing Pelco’s ExSite ™ EHXM Series explosionproof system. Your new system features a high resolution camera/optics package with programmable software. This manual is designed to be a reference tool for the operation and programming of your system. Inside yo...
Page 7 - How to Operate Your System
C1301M (6/05) 7 How to Operate Your System Operation How to Control Zoom Far To zoom far, do the following: 1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the 32X zoom limit. 2. Release the button or joystick for one second. 3. To continue zooming (digitally), press...
Page 9 - Quick Start Guide – System Setup; Quick Programming Guide; Presets
C1301M (6/05) 9 Quick Start Guide – System Setup Quick Programming Guide Access the main menu (preset 95). Refer to Accessing Main Menu (Preset 95) section. Use the joystick to position the cursor beside menu selection. If your controller does not have a joystick, use the up or down key. Press Iris ...
Page 11 - Language
C1301M (6/05) 11 Quick Programming Guide (See Page 9) Language The language for the on-screen menus is selectable. Available languages include English, Spanish, French, German, Italian, Portuguese, Polish, Russian, Turkish, and Czecholslovakian. The factory default language is English. To change the...
Page 12 - System Information
12 C1301M (6/05) System Information The System Information screen displays ExSite model, software version, available memory, and other diagnostic information. System settings cannot be changed using this screen. This screen is for reference only. Use the following steps to display the System Informa...
Page 13 - Display Setup
C1301M (6/05) 13 Quick Programming Guide (See Page 9) Display Setup Display setup allows you to program how labels are displayed on the monitor. The following labels are available: PRESET LABEL Identifies preset. ZOOM Identifies the amount of magnification. ALARM MESSAGE Displays activated alarm. A ...
Page 14 - LABEL POSITIONS
14 C1301M (6/05) LABEL POSITIONS Labels can be placed anywhere on the monitor. This feature allows you to customize the appearance of your monitor screen. The following labels are not set at fixed positions: Preset Label Alarm 1Zoom To set a label position: 1. Use the joystick to position the cursor...
Page 15 - Unit Settings; CAMERA; TYPE OF LIGHTING
C1301M (6/05) 15 Quick Programming Guide (See Page 9) Unit Settings CAMERA TYPE OF LIGHTING Pelco has calibrated settings that optimize the white balance, and the picture, for indoor and outdoor lighting conditions. There are two settings: OUTDOOR (default)INDOOR AUTO FOCUS Auto focus allows the len...
Page 16 - Auto IR Level
16 C1301M (6/05) IR CUT FILTER (23X DAY/NIGHT CAMERA) ExSite EHXM has two modes of operation: color, and black-white. You can increase sensitivity in low light conditions by switching to black-white mode (removing the IR cut filter). Color mode is preferred in normal lighting conditions. The followi...
Page 17 - ADVANCED CAMERA SETTINGS; SHUTTER SPEED; AGC LIMIT
C1301M (6/05) 17 Quick Programming Guide (See Page 9) ADVANCED CAMERA SETTINGS SHUTTER SPEED Shutter speed is the duration of the electronic shutter. Program shutter speed to operate automatically (Auto) or manually (Numeric Value). AUTO (default) The electronic shutter speed is set automatically by...
Page 18 - AUTO IRIS; Auto Iris Level; AUTO SHARPNESS
18 C1301M (6/05) AUTO IRIS Auto iris is the lens function that automatically opens and closes the iris in response to changing light conditions. Program the auto iris to operate automatically or at a user-defined level. OFF Auto iris is disabled, and control is always manual. AUTO (default) The iris...
Page 19 - VIDEO LEVEL
C1301M (6/05) 19 Quick Programming Guide (See Page 9) BACKLIGHT COMPENSATION (BLC) If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The system uses the center of the picture to adju...
Page 20 - OTHER; PARK TIME; Park Action
20 C1301M (6/05) OTHER PARK TIME This feature allows the system to begin a specified operation (preset or pattern) after a programmed time of inactivity. Park time can be programmed from 1 minute to 720 minutes (12 hours), or set to zero, which disables this feature. The default setting is zero. Par...
Page 21 - POWER UP; POWER UP ACTION
C1301M (6/05) 21 Quick Programming Guide (See Page 9) POWER UP POWER UP ACTION This setting defines a specific activity to be performed in the event the power to the system is cycled. The following settings are available: NONE No action. AUTO (default) The camera maintains its previous camera settin...
Page 22 - LINE SYNC
22 C1301M (6/05) LINE SYNC Line sync refers to a programmable function that allows you to synchronize all cameras within a matrix system. NOTE: ExSite EHXM automatically senses V-sync input. No line sync setup is required for Pelco control systems that provide a V-sync signal. For matrix systems tha...
Page 23 - PRESETS
C1301M (6/05) 23 Quick Programming Guide (See Page 9) PRESETS The ExSite EHXM system has 80 programmable preset positions. Each preset can be programmed to use all programmable camera settings, and motion detection. The presets are numbered 1-32 and 35-82. Use the following steps to program a preset...
Page 26 - PATTERNS
26 C1301M (6/05) PATTERNS A pattern is a memorized, repeating, series of zoom and preset functions that can be recalled with a command from a controller or automatically by a programmed function (alarm or power-up). The ExSite EHXM can handle up to four user-defined patterns. Pattern length is based...
Page 27 - WINDOW BLANKING
C1301M (6/05) 27 Quick Programming Guide (See Page 9) WINDOW BLANKING Window blanking allows a user to program up to eight, four-sided, user-defined areas that cannot be viewed by the operator of the system. A blanked area will automatically adjust in size as the lens zooms telephoto and wide. ExSit...
Page 29 - ALARMS
C1301M (6/05) 29 Quick Programming Guide (See Page 9) ALARMS The ExSite EHXM system has seven alarm inputs, which can be programmed as high, medium or low priority. When an alarm is received, an input signal to the unit triggers the user-defined action (go to preset, run pattern, etc.) programmed fo...
Page 31 - WIPER; WIPER CONTROL; WIPER DWELL
C1301M (6/05) 31 Quick Programming Guide (See Page 9) WIPER The following EHXM unit models feature a window wiper to clear moisture from the window of the enclosure: EHXM31C22-2 EHXM31C22-2X EHXM31C22-7 EHXM31C22-7X EHXM31CBW23-2 EHXM31CBW23-2X EHXM31CBW23-7 EHXM31CBW23-7X NOTE: The Wiper menu is on...
Page 32 - SET WASHER SEQUENCE
32 C1301M (6/05) SET WASHER SEQUENCE An external washer (not supplied by Pelco) can be used to wash the window of the enclosure. Accessing AUX 3 or selecting Preset 87 will start the washer sequence. Use the following steps to program the washer sequence. 1. Use the joystick to position the cursor b...
Page 33 - AUX
C1301M (6/05) 33 Quick Programming Guide (See Page 9) AUX An auxiliary output is a programmable signal from the system that can trigger another device to operate. An auxiliary output is programmable to trigger from an alarm or from a controller. An AUX 1 command from the controller will activate the...
Page 34 - CLEAR
34 C1301M (6/05) CLEAR Use this setting to clear user-defined settings or return the system to factory default settings. The following are the available CLEAR settings: ALL PRESETS Clears all presets. To clear a single preset, refer to the Presets section. ALL PATTERNS Clears all patterns. To clear ...
Page 35 - PASSWORD
C1301M (6/05) 35 Quick Programming Guide (See Page 9) PASSWORD ExSite EHXM features password protection to prevent unauthorized changes to the system settings. An operator can open the System Information and Display Setup Screens, but cannot access any of the Unit Settings menus. Controller/keyboard...
Page 37 - Software/Language File Upload; UPLOAD ICON
C1301M (6/05) 37 Quick Programming Guide (See Page 9) Software/Language File Upload The ExSite EHXM system allows access for on-site setup, testing, and uploading of revised operating software and language files. A Pelco field service tool is required to perform these operations. Field service tools...
Page 38 - Specifications
38 C1301M (6/05) Specifications *Manual control of camera setup functions can be done with CM6700, CM6800, CM8500, CM9500, CM9740, CM9760, CM9770, CM9780, KBD200A, KBD300A, and MPT9500 controllers, but not with CM7500, MPT9000 or KBD9000 controllers. Camera Day/Night (23X) Color LowLight ™ (22X) Col...
