Pelco C10CH-7X - Manual

C2947M-D (6/08)
C10CH Series Camera
Quick Start Guide

This quick start guide describes how to install and configure the C10CH Series camera in most
applications. It contains a representation of the setup menus to help you locate and change specific
settings.

Refer to the enclosed CD for the following documentation:

•

Installation/Operation manual: C2946M

•

Quick Start Guide: C2947M

•

Important Safety Instructions: SAFETY.PDF

MODELS

C10CH-6

1/3-inch ultra high resolution color, CCD camera, 24 VAC or 12 VDC, NTSC format

C10CH-6X

1/3-inch ultra high resolution color, CCD camera, 24 VAC or 12 VDC, PAL format

C10CH-7X

1/3-inch ultra high resolution color, CCD camera, 220 to 240 VAC, PAL format

ì

Camera Mount

î

Back Focus Locking Screw

ï

Lens Mount

ñ

Auto Iris Lens Connector

ó

Setup Button

r

Ground Screw

s

Power Connector

•

C10CH-6/6X, Power Terminal Block

•

C10CH-7X, Power Cord

t

Video Output Connector

C10CH-7X BACK

SETUP MENUS

The camera default settings are set at the factory to operate in most applications and lighting conditions,
and normally require no adjustments. Sometimes, however, adjustments may be necessary.

Use the setup menus to customize the camera settings for your application as needed. Refer to the
Installation/Operation manual (C2946M) for complete instructions and explanations of camera settings.

ALL SETTING ARE
INITIALIZED

OK

C

AN

C

EL

RESTORE FA

C

TORY SETTING

-> OFF

TITLE
EDIT TITLE

BA

C

K EXIT

TITLE

-> OFF
-> -2
-> 0

MASK
MASK

C

OLOR

MASK EDIT
MASK ERASE

BA

C

K EXIT

MASKING

-> AUTO
-> 38

LINE SYN

C

V-PHASE ADJ

BA

C

K EXIT

LINE SYN

C

-> OFF
-> 17
-> 4

E

C

LIPSER

THRESHOLD
LEVEL

BA

C

K EXIT

E

C

LIPSER

#.##
#.##

->

FIRMWARE VERSION
OSD VERSION

RESTORE FA

C

TORY SETTINGS

RETURN END

SYSTEM INFORMATION

C

OVER THE LENS

AND PRESS OK

OK

C

AN

C

EL

PIXEL

C

ORRE

C

TION

C

URRENT SETTING

ARE SAVED

OK

C

AN

C

EL

SAVE AS

C

USTOM

-> AUTO
-> AUTO
->
-> 60%
-> SHARP
-> SHORT
->
->

LINE SYN

C

WHITE BALAN

C

E

C

HROMA

GAMMA
SHARPNESS

C

ABLE

C

OMPENSATION

MASKING
TITLE

BA

C

K EXIT

FUN

C

TION SET.

-> ES

C

-> OFF
-> -8
-> OFF
-> LOW

AUTO EXPOSURE
E

C

LIPSER

D

C

IRIS LEVEL

FLI

C

KERLESS

AG

C

BA

C

K EXIT

EXPOSURE SET.

STANDARD
GAMING

C

USTOM

BA

C

K EXIT

PROFILES

EXIT

->
->
->
->
->
->

PROFILES
EXPOSURE SET.
FUN

C

TION SET.

SAVE AS

C

USTOM

PIXEL

C

ORRE

C

TION

SYSTEM INFORMATION

MAIN MENU

ACCESSING THE SETUP MENUS

Use the 5-position button controller on the side panel of the camera to access and navigate the on-screen
display (OSD) menus. Use the following table to navigate through the menu options.

LENS

The C10CH Series camera supports both manual and auto iris lenses, either fixed focal length or
varifocal. It automatically senses an auto iris lens as soon as you plug in the connector.

The camera has a standard CS mount that can accept a C mount lens with a PCMA40 lens adapter.

To mount the lens onto the camera:

1. Make sure the lens does not touch the camera imager when installed.

2. Use clean, compressed air or a clean, dry lens cloth to make sure there is no dust or other foreign

matter between the lens and the camera imager.

3.

C mount lens:

Screw the adapter onto the lens.

4. Screw the lens onto the lens mount.

5.

Auto iris lens:

Connect the 4-pin connector from the lens to the connector on the side of the

camera.

6. Perform the lens focusing procedure before using the lens (refer to

Lens Focus

).

Menu Options

Navigating the Menu

Display the MAIN MENU on the screen.

Press and hold down the center button for two
seconds.

Move the cursor up or down in a menu or toggle
through menu selections.

Move the button up or down.

Move the cursor right or left in a menu.

Move the button left or right.

Select a menu or make a menu selection.

Press the center button.

Save a setting and then return to the menu.

Press the center button.