Pelco 500 Series - Manual

6 C2937M-A (5/07) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

C2937M-A (5/07) 7 Description The 500 Series high performance LCD monitors are designed specifically for the security industry and provide high quality display of video or computer signals using multiple inputs. Adjustments of standard monitor display parameters are made using user-friendly, on-scre...

8 C2937M-A (5/07) PACKAGE CONTENTS 1 23-, 26-, 32-, 37-, or 42-inch TFT LCD monitor with attached stand (removable) 1 US standard power cord 1 EU standard power cord 1 DVI cable 1 VGA cable with 15-pin D-sub connection 1 Remote control unit 2 AAA batteries 1 Installation/Operation manual Figure 1. P...

C2937M-A (5/07) 9 Installation MOUNTING The monitor can be placed on any flat surface (desk or table), or it can be wall mounted. NOTE: Only use a recommended Pelco mount for these LCD monitors. • For the 23-, 26-, and 32-inch models, Pelco recommends the PMCL-WMT tilt wall mount, the PMCL-CM or PMC...

10 C2937M-A (5/07) REAR PANEL CONNECTORS Figure 2. Rear Panel Connectors 1. RS-232C: For authorized service use. 2. DVI: Connection to digital video signals from a computer or any Pelco device with DVI output, especially PMVC4 and PMVR2 multiviewers. 3. RGB (VGA): (Loop through is disabled; for futu...

C2937M-A (5/07) 11 Operation FRONT PANEL CONTROLS Figure 3. Front Panel Controls 1. Input: Displays the main on-screen menu. 2. Source: Selects the input source and confirms your choice. 3. ! and " : Navigates through the on-screen menu. 4. Vol: Increases ( # ) or decreases ( $ ) the volume. Als...

12 C2937M-A (5/07) INSTALLING REMOTE CONTROL BATTERIES Figure 4. Battery Installation Refer to Figure 4 for the following procedure. 1. Open and remove the battery cover on the back of the remote control. 2. Install two AAA size batteries (supplied). Match the + and – signs on the batteries to the s...

C2937M-A (5/07) 13 REMOTE CONTROL FUNCTIONS Figure 5. Remote Control Functions

14 C2937M-A (5/07) 1. POWER: Turns on or off power to the monitor. 2. (input source): Displays all the available input sources. Press the button to select the desired input source. 3. SCAN: Changes the scan mode of the screen (4:3, 14:9, Over Scan, 16:9). 4. BLUE ONLY: Turns off the red and green co...

18 C2937M-A (5/07) RGB/DVI Mode Menu Field Definitions NOTE: You cannot change the language on this menu. You must use the Video1, Video2, S-Video, Component Mode Menu to change the language. The language will then be changed for both menus. Input: Select RGB or DVI. Contrast: Adjusts black level of...

C2937M-A (5/07) 19 Maintenance If the quality of the picture is poor and cannot be improved by making adjustments on the front control panel, inspect all system connections and cable runs. CLEANING • Gently wipe your screen with a clean camel hair brush or a soft, clean, lint-free cloth. • Gently ap...

20 C2937M-A (5/07) Supported Input Modes *If the display is distorted or shifted at a resolution of 1366 x 768, you should adjust the resolution in Auto Position Override on the on-screen display menu: MENU>AUTO POSITION OVERRIDE>1366 X 768. Mode Resolution H Freq. (kHz) V Freq. (Hz) 0 720 x 4...

C2937M-A (5/07) 21 Specifications MODELS PMCL523 23-inch (583 mm) LCD monitor PMCL526 26-inch (660 mm) LCD monitor PMCL532 32-inch (800 mm) LCD monitor PMCL537 37-inch (940 mm) LCD monitor PMCL542 42-inch (1,067 mm) LCD monitor GENERAL Native Resolution 1366 x 768 WXGA Panel Aspect Ratio 16:9 Viewin...