Page 2 - CONTENTS
2 Pelco Manual C682M-E (11/01) CONTENTS IMPORTANT SAFEGUARDS AND WARNINGS ...................................................... 5 DESCRIPTION ................................................................................................................ 6 MODELS ......................................
Page 3 - LIST OF TABLES; SPECIFICATIONS; LIST OF ILLUSTRATIONS
Pelco Manual C682M-E (11/01) 3 LIST OF TABLES A Video Coaxial Cable Requirements ................................................................... 7 INSTALLING THE DX7000CD (CD-RW Drive) ...................................................... 38 LOADING THE DIRECTCD SOFTWARE ..........................
Page 5 - IMPORTANT SAFEGUARDS AND WARNINGS; IMPORTANT
Pelco Manual C682M-E (11/01) 5 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and con-form to all local codes. 2. Unless the unit is specifica...
Page 6 - DESCRIPTION; MODELS; Qty; WARNING; before applying power
6 Pelco Manual C682M-E (11/01) DESCRIPTION The DX7000 Series are high-quality digital video recorders (DVR) that combine the functionsof a recorder and multiplexer into a product with versatile recording and playback functions.The units are capable of dual operation and can record and play back vide...
Page 7 - INSTALLATION; Figure 1. Rear View of Back Panel; Refer to Table A for video coaxial cable distances.; Table A. Video Coaxial Cable Requirements
Pelco Manual C682M-E (11/01) 7 INSTALLATION Place the DVR on any flat surface (desk or table) or install in any standard 19-inch (48.26 cm)wide console or rack configuration. Figure 1. Rear View of Back Panel 1 Camera Inputs – Refer to Table A for video coaxial cable distances. 2 Alarm Inputs 3 Anal...
Page 8 - TWO-WIRE CONTROL SYSTEM INSTALLATION; Receiver; Set the DTE/DCE switch located on the bottom of the converter to DCE.; Figure 2. Two-Wire Control System Installation; The PTZ must be; Figure 3. Multiple PTZ Installation
8 Pelco Manual C682M-E (11/01) TWO-WIRE CONTROL SYSTEM INSTALLATION 1. Connect the control wires from the receiver to the RS-422 converter. The DX7000 cansupport up to 16 PTZ devices. To connect more than one PTZ to the system, refer toFigure 3. RS-422 Converter Receiver TX+ RX+ TX- RX- 2. Set the D...
Page 9 - PROGRAMMING; Figure 5. Display Mode; DISPLAY MODE; Alarm Status Display –; Motion Detection Status –
Pelco Manual C682M-E (11/01) 9 PROGRAMMING Turn the system power ON; the Main Screen (DISPLAY mode) appears. Figure 5. Display Mode DISPLAY MODE 1 Date and Time Indicator – Displays current date and time. 2 SEARCH Button – Plays back and search recordings by date and time. 3 SETUP Button – Programs ...
Page 10 - CAMERA SETUP; Figure 6. Channel Setup Menu; CAMERA NAME Box; Selection must correspond with the NTSC/PAL selection switch; CAMERA ENABLE Button; Use the following steps to set up a camera site.
10 Pelco Manual C682M-E (11/01) DX7000 SYSTEM SETUP To setup the DX7000 Digital Video Recorder use the left mouse button and click on theSETUP button located in the DISPLAY mode. CAMERA SETUP Figure 6. Channel Setup Menu 1 CAMERA NAME Box 2 SIGNAL TYPE – Selection must correspond with the NTSC/PAL s...
Page 11 - COLOR SETUP; Figure 7. Color Setup Menu
Pelco Manual C682M-E (11/01) 11 COLOR SETUP Figure 7. Color Setup Menu 1 CON – Adjusts the CONTRAST of the viewed and recorded scene. 2 BRI – Adjusts the BRIGHTNESS of the viewed and recorded scene. 3 RED – Adjusts the RED level of the viewed and recorded scene. 4 GREEN – Adjusts the GREEN level of ...
Page 12 - SCHEDULE SETUP; Figure 8. Schedule Setup Menu
12 Pelco Manual C682M-E (11/01) SCHEDULE SETUP Figure 8. Schedule Setup Menu 1 GROUP (01-24) – Selects group to be scheduled. 2 Sets START TIME and END TIME for recording group. 3 Schedule Selection Buttons CLEAR ALL SCHEDULE – Clears all GROUP (1-24) schedules. FULL RECORD – Adds all cameras and da...
Page 14 - SPEED SETUP; Figure 9. Speed Setup Menu
14 Pelco Manual C682M-E (11/01) SPEED SETUP Figure 9. Speed Setup Menu 1 RECORDING SPEED MODE a. NORMAL – Sets recording speed for continuous recording. b. MOTION – Sets motion detection and pre-alarm recording speeds. c. SENSOR – Sets sensor detection and pre-alarm recording speeds. 2 IMAGE QUALITY...
Page 15 - MOTION DETECTION SETUP; Figure 10. Motion Detection Setup Menu; BEEP –; Beeps when motion is detected.; SENSITIVITY –; Adjusts the sensitivity of the detection areas.; CLEAR ALL BLOCK –; Deletes all motion detection area blocks.
Pelco Manual C682M-E (11/01) 15 MOTION DETECTION SETUP Figure 10. Motion Detection Setup Menu 1 BEEP – Beeps when motion is detected. 2 SENSITIVITY – Adjusts the sensitivity of the detection areas. 3 CLEAR ALL BLOCK – Deletes all motion detection area blocks. 4 Motion Detection Area – To select a de...
Page 16 - PASSWORD SETUP; Figure 11. Password Setup Menu; SELECT LEVEL –
16 Pelco Manual C682M-E (11/01) PASSWORD SETUP Figure 11. Password Setup Menu 1 SELECT LEVEL – Levels include Administrator, Search User, PTZ/Backup User, and Client User. 2 INPUT AREA – Password input window. 3 NUMBER BUTTONS – Use number buttons to input password. 4 ENTER – Select to apply passwor...
Page 17 - Figure 12. Pan and Tilt Protocol Menu; QUIT TO EXPLORER; Select; to return to the DX7000 system DISPLAY mode.
Pelco Manual C682M-E (11/01) 17 PAN & TILT SETUP Figure 12. Pan and Tilt Protocol Menu 1 Select pan and tilt protocol by scrolling through the selections in the RX TYPE box. QUIT TO EXPLORER The DX7000 uses a Window’s based operating system. To set a network address, addhardware, or change clock...
Page 18 - OPERATION; RECORDING STATUS; To change screen view:; PTZ CONTROL MODE; Use the buttons to pan left and right.; Figure 13. PTZ Controls
18 Pelco Manual C682M-E (11/01) OPERATION RECORDING STATUS The colored circle located to the right of the on-screen camera title indicates the recordingstatus of the camera. RED indicates that the camera is recording continuously. If the circleis BLUE, camera recording was triggered by motion detect...
Page 21 - SEARCH CONTROL MODE; Figure 15. Search Control Menu
Pelco Manual C682M-E (11/01) 21 SEARCH CONTROL MODE Figure 15. Search Control Menu 1 Date and Time Indicator – Displays current date and time. 2 Search Date – Displays year, month, and time of search. 3 Search Window – Flashes when system is searching through cameras. 4 Search Index Button – Shows o...
Page 22 - SELECT DATE AND TIME; Click the CALENDAR BUTTON.; Figure 16. Playback Control Buttons; INDEX SEARCH; Enter the START TIME and END TIME of search.
22 Pelco Manual C682M-E (11/01) SELECT DATE AND TIME 1. Enter the year and month in the SEARCH DATE area of the menu. Click the up ordown arrow buttons to make a selection. 2. Enter the hour and minute in the SEARCH DATE area of the menu. Click the arrowbuttons up or down to make a selection. 3. Cli...
Page 24 - To install the remote users software:; Figure 17. DX7000 Series Remote User Software Installation Menu; Screen
24 Pelco Manual C682M-E (11/01) REMOTE SITE SOFTWARE DESCRIPTION Free remote site software is included with the DX7000 to provide remote site viewing of liveand recorded video. The software is compatible with Windows 98 and Windows 2000. INSTALLATION To install the remote users software: 1. Start Wi...
Page 25 - REGISTERED SITE SETUP; Figure 18. Setup Screen
Pelco Manual C682M-E (11/01) 25 REGISTERED SITE SETUP Figure 18. Setup Screen 1 Date and Time Indicator – Displays current date and time. 2 SITE NAME – Enters the name of the site. 3 ADDRESS – Inputs the IP address or phone number of site. 4 PASSWORD – Use only if the DX7000 registered site is CLIEN...
Page 26 - Figure 19. Online Mode
26 Pelco Manual C682M-E (11/01) OPERATION Figure 19. Online Mode 1 Date and Time Indicator – Displays current date and time. 2 SEARCH Button – Plays back and searches recordings by date and time. 3 PTZ Control Button – Controls pan, tilt, and zoom functions. 4 CONNECT/DISCONNECT Button – Connects to...
Page 27 - Screen Division –; Single camera display
Pelco Manual C682M-E (11/01) 27 9 Screen Division – Single camera display Displays cameras 1-9 Quad display, cameras 1-4 Displays cameras 10-16 Quad display, cameras 5-8 Displays all 16 cameras Quad display, cameras 9-12 Sequencing mode – Sequence usingsingle, four, or nine camera displays. Quad dis...
Page 28 - VIEW; Figure 20. PTZ Controls
28 Pelco Manual C682M-E (11/01) VIEW It is not necessary to use the screen division buttons located in the lower left corner of thescreen to change the camera view. You can use the left and right mouse buttons to in-stantly view a single camera or remove the menu bars from the display. To change scr...
Page 29 - Click the PTZ button in the DISPLAY Mode. The PTZ Mode appears.; PRESETS; Click the MOVE button.
Pelco Manual C682M-E (11/01) 29 PATTERN A pattern is a user-defined, viewable camera path with a definite beginning and end.The pattern can consist of any standard pan and tilt or lens commands. Once defined thepattern is easily activated with the press of an on-screen menu button. The pattern will ...
Page 30 - Figure 21. Pattern and Preset Bars; PRESET TOURS
30 Pelco Manual C682M-E (11/01) Figure 21. Pattern and Preset Bars PRESET TOURS A preset tour is a programmed sequential execution of preset positions. How to Run A Preset Tour 1. Click the PTZ button in the DISPLAY Mode. The PTZ Mode appears. 2. Click the left mouse button on PRESET. 3. Click the T...
Page 31 - SEARCH MODE; Figure 22. Search Mode
Pelco Manual C682M-E (11/01) 31 SEARCH MODE Figure 22. Search Mode 1 Date and Time Indicator – Displays current date and time. 2 Search Date – Selects month and year to search video. 3 Search Time – Selects the time (hour and minute) to search video. 4 Select Camera – Reviews video of selected camer...
Page 32 - Figure 23. Playback Control Buttons
32 Pelco Manual C682M-E (11/01) SELECT DATE AND TIME 1. Enter the year and month in the SEARCH DATE area of the menu. Click the up ordown arrow buttons to make a selection. 2. Enter the hour and minute in the SEARCH DATE area of the menu. Click the arrowbuttons up or down to make a selection. 3. Cli...
Page 33 - EMERGENCY AGENT SOFTWARE; Figure 24. Emergency Agent Window; To install the Emergency Agent software:; For the Emergency
Pelco Manual C682M-E (11/01) 33 EMERGENCY AGENT SOFTWARE Figure 24. Emergency Agent Window Emergency Agent software alerts the remote site client of any triggered alarm at the surveil-lance site. When an alarm is triggered a popup widow appears on the monitor of the remotesite client. The window dis...
Page 34 - BACKUP VIEWER SOFTWARE; To install the Backup Viewer:
34 Pelco Manual C682M-E (11/01) BACKUP VIEWER SOFTWARE Use the Backup Viewer software to search images stored on backup media, DAT tape orDVD disc. To install the Backup Viewer: 1. Start Windows 98. 2. Close all programs, including any anti-virus programs. 3. Insert the Remote Users Software CD into...
Page 35 - BACKUP VIEWER OPERATION; Figure 25. Backup Viewer
Pelco Manual C682M-E (11/01) 35 BACKUP VIEWER OPERATION Figure 25. Backup Viewer 1 Date and Time Indicator – Displays current date and time. 2 Search Date – Displays year, month, and time of search. 3 Search Window – Flashes when system is searching through cameras. 4 Search Index Button – Shows or ...
Page 36 - WATERMARK TOOL; Insert the Remote Users Software CD into the CD-ROM drive.; WATERMARK TOOL OPERATION; Load the Watermark Tool.; Figure 26. The Image Has Not Been Altered
36 Pelco Manual C682M-E (11/01) WATERMARK TOOL The Watermark tool allows you to verify if an original image has been altered. The WatermarkingViewer software is available on the Remote Site Software CD. To install the WatermarkViewer: 1. Start Windows 98. 2. Close all programs, including any anti-vi...
Page 37 - Figure 27. The Image Has Been Altered; There are three indications that an image has been altered:
Pelco Manual C682M-E (11/01) 37 Figure 27. The Image Has Been Altered There are three indications that an image has been altered: 1. A red frame around the image. 2. The image is shaded. 3. The message “Image has been altered or has not been watermarked” appears in thelower left-hand corner of the s...
Page 38 - Do not; connect the power supply to the CD-RW drive at this time.; Figure 28. How to Connect the CD-RW Drive to the DX7000 DVR; DX7000 click the SETUP button. The SETUP mode appears.; Driver Installation Dis-; ware Wizard pops-up on the screen with the following message:
38 Pelco Manual C682M-E (11/01) INSTALLING THE DX7000CD (CD-RW DRIVE) 1. Connect one end of the USB data cable to the CD-RW drive. Connect the other end of the USB data cable to the USB serial port (1 or 2) located on the back panel of theDX7000 DVR. Do not connect the power supply to the CD-RW driv...
Page 41 - LOADING THE DirectCD SOFTWARE; hp cd-writer installation software – disc 1; HOW TO OPERATE THE CD-RW
Pelco Manual C682M-E (11/01) 41 LOADING THE DirectCD SOFTWARE 1. From the DISPLAY mode of the DX7000 click on the SETUP button. The SETUPmode appears. 2. Click the EXIT TO EXPLORER button. Windows Explorer appears. 3. Insert the hp cd-writer installation software – disc 1 into the CD-RW drive. 4. Se...
Page 42 - PREPARING CD-RW MEDIA FOR BACKUP; The Initial Formatting of CD-RW Media Using the DX7000 DVR; Click the EXIT TO EXPLORER button. Windows Explorer appears.
42 Pelco Manual C682M-E (11/01) PREPARING CD-RW MEDIA FOR BACKUP NOTE: The initial format of a CD-RW disk can take a considerable amount of time, approximately three hours. To speed up the procedure of copying files to a backupdevice, always have a formatted CD-RW disc readily available. The Initial...
Page 44 - BACKUP WINDOW; SPACE NEEDED indicator –
44 Pelco Manual C682M-E (11/01) BACKUP WINDOW Figure 29. Backup (COPY) Window 1 SELECT DRIVE box – Lists drives with files available for backup. 2 STORED ITEMS box – Lists all files stored in the selected drive. 3 ADD button – Adds stored files to ITEMS TO BACKUP box. 4 ITEMS TO BACKUP box – Lists f...
Page 45 - Click the COPY button. The backup window appears.; Figure 30. Storage Indicator is now Labeled BACKUP
Pelco Manual C682M-E (11/01) 45 HOW TO BACKUP (COPY) TO THE CD-RW DRIVE 1. From the DISPLAY mode of the DX7000, click the COPY button. The SETUP modeappears. NOTE: If the COPY button is not available it has not been initiated. Refer to the Initiate DX7000 Copy Button section of this manual. 2. Click...
Page 46 - CONNECT THE EXTERNAL MODEM TO THE DX7000; Connect the other end of the cable to the telephone wall jack.; Figure 31. How to Connect the External Modem to the DX7000 DVR
46 Pelco Manual C682M-E (11/01) DX7000EM (External Modem) CONNECT THE EXTERNAL MODEM TO THE DX7000 1. Connect the 25-pin end of the RS-232 cable (supplied with the modem) to the serialport located on the back panel of the modem. 2. Connect other end of the RS-232 cable to the COM 2 serial port locat...
Page 47 - LOAD THE DRIVER FOR THE MODEM; located on the front panel.
Pelco Manual C682M-E (11/01) 47 LOAD THE DRIVER FOR THE MODEM 1. From the DISPLAY mode of the DX7000, click the EXIT button. A dialog box appears. Select Yes. The DX7000 shuts off. 2. Turn ON the modem and restart the DX7000 system by pushing the ON/OFF switch located on the front panel. 3. The DX70...
Page 50 - GENERAL
50 Pelco Manual C682M-E (11/01) SPECIFICATIONS ELECTRICAL/VIDEO Input Voltage: 100-240 VAC switchable, 50/60 Hz Signal System: NTSC/PAL CPU & RAM DX7008: Celeron, 128 MB DX7016: Pentium ® III, 128 MB Resolution NTSC: 320 x 240 PAL: 384 x 288 Compression: M-JPEG Compressed Image Size: 52 x 240; a...
Page 51 - NOTES
Page 52 - REVISION HISTORY; PRODUCT WARRANTY AND RETURN INFORMATION
® Pelco, the Pelco logo, Spectra, Genex, and Legacy are registered trademarks of Pelco. © Copyright 2001, Pelco ™ Esprit and Camclosure are trademarks of Pelco. All rights reserved. ® Windows is a registered trademark of Microsoft.® Pentium is a registered trademark of Intel.™ DirectCD is a trademar...
