Pelco 310 - Manual - manualsarea.com

Page 3 - Contents

C2496M-A (1/06) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . ...

Page 4 - Important Safety Instructions; RISK OF ELECTRIC SHOCK.

4 C2496M-A (1/06) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such...

Page 5 - REGULATORY NOTICES; RADIO AND TELEVISION INTERFERENCE

C2496M-A (1/06) 5 REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 6 - Description; Installation; PREPARE WALL OR CEILING

6 C2496M-A (1/06) Description The 310 Series Camclosure ® integrated camera system is a track-light design that mounts to a wall or ceiling. The system incorporates a camera and lens package into a small, unobstructive, medium-security enclosure designed for areas subject to vandalism. The system is...

Page 8 - CONNECT VIDEO AND POWER

8 C2496M-A (1/06) CONNECT VIDEO AND POWER 1. Some indoor installations do not require a heater. If the installation does not require a heater, disconnect the heater wiring. a. Remove the cover with the supplied 1/8-inch hollow screwdriver bit. b. Remove the camera from the mounting bracket, and unpl...

Page 9 - ATTACH BASE; ADJUST ENCLOSURE

C2496M-A (1/06) 9 ATTACH BASE Release the base locking ring for access to the mounting holes. To attach the base to an adapter plate or conduit adapter, two 6-32 x 1.25-inch tamper-resistant screws are supplied with the adapters. Use the 1/8-inch hollow screwdriver bit supplied with the Camclosure. ...

Page 10 - AUTO IRIS LEVEL ADJUSTMENT

10 C2496M-A (1/06) Adjustments (Color Camera Only) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however, adjustments may be necessary. 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vertical phase, iri...

Page 11 - SWITCH SETTINGS FOR VARIFOCAL LENS; AE Functions; Switch Number and Position

C2496M-A (1/06) 11 SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. For manually setting and locking the white balance, place a white background in front of camera and turn off switch 1. For gamma co...

Page 12 - SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS; Manual backlight compensation:

12 C2496M-A (1/06) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there...

Page 14 - Specifications; General

14 C2496M-A (1/06) Specifications General Pan/Tilt Adjustment Manual; 180° pan; 180° tilt Construction Aluminum base and cover, steel camera mounting bracket Finish Gray polyester powder coat Environment Low temperature, indoor/outdoor Operating Temperature -50° to 122°F (-46° to 50°C); de-ices to -...

Page 15 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic...

Pelco 310 - Manual

Table of Contents:

Summary

Other Pelco Models