Pelco 13M2.8-12 - Manual
Pelco 13M2.8-12 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Operation; ADJUSTING THE ZOOM; Setting the Focus; SETTING THE FOCUS
- Page 3 – Routine Servicing; Be careful not to damage the lens while cleaning.; Specifications
- Page 4 – PRODUCT WARRANTY AND RETURN INFORMATION
C785M-A (1/09)
3 Megapixel Lenses
Installation/Operation
Important Safety Instructions
WARNINGS:
Prior to installation and use of this product, the following items should be observed.
•
Servicing should be done only by qualified service personnel.
•
Only use replacement parts recommended by Pelco.
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
Description
These lenses are varifocal lenses designed for 1/3-inch megapixel cameras with 3 megapixels (MPx) or less in resolution. These lenses, which were
designed for CS-mount cameras, produce high precision images from the image center to the image corner, fully exploiting the performance of megapixel
cameras. Megapixel lenses are best suited for high-quality image surveillance with a megapixel camera as well as with a standard definition camera.
MODELS
13M2.2-6
1/3-inch megapixel, varifocal lens; 2.2~6.0 mm; f/1.3~2.0 auto iris; CS mount
13M2.8-8
1/3-inch megapixel, varifocal lens; 2.8~8.0 mm; f/1.2~1.9 auto iris; CS mount
13M2.8-12
1/3-inch megapixel, varifocal lens; 2.8~12.0 mm; f/1.4~2.7 auto iris; CS mount
13M15-50
1/3-inch megapixel, varifocal lens; 15~50.0 mm; f/1.5~2.1 auto iris; CS mount
Installation
1. Press the threaded portion of the lens mount against the threaded portion of the camera mount.
2. Slowly rotate the lens clockwise.
3. Screw in the lens mount.
4. Connect the auto iris lens cable to the electrical connector on the camera.
NOTE:
The lens mount is equipped with a slip mechanism. To change the rotational position of the lens, rotate the lens until it reaches the stop (cannot be
rotated further), and then rotate it counterclockwise to the required position.
Figure 1.
Lens and Connector Wiring
1
2
4
3
OPEN
DAMP.
C
OIL
OPEN
DRIVE
C
OIL
LENS
C
ONNE
C
TOR
4-PIN PLUG
The i
r
is
c
ont
r
ol fo
r
this lens
c
annot be a
c
tivated with a video signal.
Use a
c
ame
r
a that
c
an send a D
C
signal.
NOTE:
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Operation ADJUSTING THE ZOOM NOTE: The lens is a varifocal lens. After a zoom operation, you will need to set the focus. 1. Loosen the zoom tightening knob. 2. Rotate the zoom ring to select the appropriate angular field of view. • Rotate the ring to “W” to set the zoom to wide. • Rotate the ring to...
Routine Servicing A special coating has been applied to the lens surface to prevent light reflection. A dirty lens surface due to dust, oil, or fingerprints causes harmful glare, which degrades the lens properties. Dirt can also cause mold or scratches on the lens. NOTE: Be careful not to damage the...
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years: – Fiber optic products– TW3000 ...
