Pelco 10P08 - Manual - manualsarea.com

Page 2 - CONTENTS; LIST OF ILLUSTRATIONS

2 Pelco Manual C1441M-D (1/98) CONTENTS Section Page 1.0 GENERAL3 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 3 2.0 DESCRIPTION .......................................................................................... 4 2.1 MODELS .............................................

Page 3 - Only use replacement parts recommended by Pelco.; The product and/or manual may bear the following marks:; RISK OF

Pelco Manual C1441M-D (1/98) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation an...

Page 5 - Back Focus Adjustment

Pelco Manual C1441M-D (1/98) 5 3.0 INSTALLATION The camera and lens package are installed at the factory. 3.1 ADJUSTMENTS Your optics package comes from the factory adjusted for a broad range of lightingconditions. For this reason, you may find it necessary to adjust your optics packageto tailor the...

Page 6 - Auto Iris; Set the AGC control in the “ON” position.

6 Pelco Manual C1441M-D (1/98) ➤ Auto Iris Level is adjusted using a video meter to provide a video signal output of be-tween 130 and 142 IRE (Institute of Radio Engineers; 1V p–p = 100 IRE’s)when lighting from skylights, low pressure sodium lights and fluorescent lightsare present. ALC is adjusted ...

Page 7 - . Use the tip of a ballpoint pen or similar instrument to

Pelco Manual C1441M-D (1/98) 7 3.1.5 V-Phase (Vertical Phase) V-Phase (Vertical Phase) is valuable when multiple optic packages are switched bya sequential or matrix switcher. The vertical phase +/- buttons are used to compen-sate for vertical phase discrepancies which will occur in a multiple camer...

Page 8 - Shutter; Color Camera Adjustments

8 Pelco Manual C1441M-D (1/98) Figure 3. Black and White Camera Adjustments Table A. Shutter Speeds Shutter Shutter Speed Position (in seconds) 0 1/60 1 1/100 2 1/250 3 1/500 4 1/1000 5 1/2000 6 1/4000 7 1/10,000 8 Not Used 9 Not Used SHUTTER SPEED CONTROL(YOU CAN SELECT ONE OF EIGHT SHUTTER SPEEDS;...

Page 9 - Make certain; Camera/Lens Removal and Installation

Pelco Manual C1441M-D (1/98) 9 4.0 SERVICE Should it become necessary to remove the camera/lens for service or replacement,follow the steps outlined below. Refer to Figure 4, if necessary. 1. Remove main electrical power by switching off main power switch located upinside the back box. 2. Rotate the...

Page 10 - Schematic Diagram for Color Camera/Lens; LENS

10 Pelco Manual C1441M-D (1/98) 5.0 WIRING DIAGRAM Figure 5. Schematic Diagram for Color Camera/Lens RED GREENYELLOWBLACK GRAYWHITE BROWN BLUE RED VIOLET YELLOW BLACK GRAYWHITEBROWN BLUE BROWNWHITEGRAY BLACK YELLOW VIOLET BLUEREDWHT/REDWHT/BLK 10 1 1 8 J6 J7 J1 P2 1 10 12 1 P1 4 8 1 ORG/WHTGRN/WHTWH...

Page 12 - WARRANTY AND RETURN INFORMATION; WARRANTY; RETURNS

12 Pelco Manual C1441M-D (1/98) 7.0 WARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit,Genex, Legacy, and Spectra are registeredtrademarks of Pelco.Endura and ExSite are trademarks of Pelco. © Copyright 1998, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, w...

Pelco 10P08 - Manual

Table of Contents:

Summary

Other Pelco Models