Patton 2720/I Series - Manual

Patton 2720/I Series

Patton 2720/I Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
Page: / 23

Table of Contents:

  • Page 3 – INDUSTRY CANADA NOTICE; The Canadian Department of Communications label identifies cer-; SERVICE INFORMATION; All warranty and non-warranty repairs must be returned freight; AM to 5PM EST, Monday; The CE symbol on your Patton Electronics equipment indicates
  • Page 4 – GENERAL INFORMATION; are single port T1/FT1
  • Page 5 – Ethernet LAN; Router A; S2 SUMMARY TABLE; Network
  • Page 7 – Reserved
  • Page 8 – normal font; bold type
  • Page 9 – HELPFUL HINTS; The Main Menu options are briefly described below.
  • Page 10 – D4: This is an older, but widely used, line format that does not
  • Page 12 – ESF Carrier Loops: Enabled; The ESF format provides the CO the ability to put the customer
  • Page 14 – The Model 2720 receiving a RL can be in one of the following states:
  • Page 15 – Unavailable Seconds
  • Page 16 – Rx PRM; The NetLink-T1TM transmits ANSI performance report messages; Current DIP Switch Settings; Headers 1 and 2 are provided for easy identification of your unit; Password
  • Page 17 – Figure 2. Model 2720 twisted pair line interface.
  • Page 19 – To perform an RDL test, follow these steps:; Remote Loop
  • Page 20 – APPENDIX A
  • Page 22 – APPENDIX D; INTERFACE PIN ASSIGNMENT
  • Page 23 – APPENDIX E; EIA-530 INTERFACE PIN ASSIGNMENT; Signal; PATTON ELECTRONICS MODEL 2720
Loading the manual

USER
MANUAL

MODEL 2720/I Series

NetLink-T1™
T1/Fractional T1 CSU/DSU

SALES OFFICE
(301) 975-1000
TECHNICAL SUPPORT
(301) 975-1007
http://www.patton.com

Part# 07M2720I-UM
Doc#08618U2-001,
Rev. B
Revised 10/26/06

An ISO-9001

Certified Company

Copyright © 2006

Patton Electronics Company

All Rights Reserved

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - INDUSTRY CANADA NOTICE; The Canadian Department of Communications label identifies cer-; SERVICE INFORMATION; All warranty and non-warranty repairs must be returned freight; AM to 5PM EST, Monday; The CE symbol on your Patton Electronics equipment indicates

4 3 1.3 INDUSTRY CANADA NOTICE The Canadian Department of Communications label identifies cer- tified equipment. This certification means that the equipment meetscertain telecommunications network protective, operational and safetyrequirements. The Department does not guarantee the equipment willope...

Page 4 - GENERAL INFORMATION; are single port T1/FT1

6 3.0 PPP Operational Background PPP is a protocol used for multi-plexed transport over a point-to-point link. PPP operates on all full duplex media, and is a symmetric peer-to-peerprotocol, which can be broken into three main components: 1. A standardmethod to encapsulate datagrams over serial link...

Page 5 - Ethernet LAN; Router A; S2 SUMMARY TABLE; Network

7 For example, the customer site is assigned the addresses 192.168.1.0/24 through 192.168.1.1/24. The address 192.168.1.1/24 isalso the default gateway for the remote network. The above settingsremove any routing/forwarding intelligence from the CPE. The associ-ated Cisco configuration will set seri...

Other Patton Models

All Patton Other