Patton 2888 - Manuals - manualsarea.com

Page 2 - OnSite 2888 Quick Start Guide; Powering up the OnSite; Connecting the power supply; Connect the AC power cord male plug to an AC power outlet (120–240 VAC).; DC Power

2 OnSite 2888 Quick Start Guide 1.0 Powering up the OnSite 1.1 Connecting the power supply AC Power 1. Connect the AC power cord female plug directly to the OnSite AC connector. 2. Connect the AC power cord male plug to an AC power outlet (120–240 VAC). The Power LED blinks as the OnSite is powering...

Page 3 - Connecting DC Power to the 2888 DC Power Supply; WARNING

IPLink 2884/2888 Quick Start Guide 3 Figure 1. Connecting DC Power to the 2888 DC Power Supply Figure 2. 2888 rear panel There are no user-serviceable parts in the power supply section of the Model 2888. Contact Patton Electronics Technical support at (301)975-1007, via our web site at http://www.pa...

Page 4 - Setting the IP address; Default IP configuration; The factory default IP settings are as follows:; Connecting to the PC and logging in via the Ethernet port; Connecting to the PC’s ENET port; Log into the unit using the following:; admin

4 OnSite 2888 Quick Start Guide 2.0 Setting the IP address 2.1 Default IP configuration The factory default IP settings are as follows: • LAN port (ETH 0): IP address: 192.168.200.10, Netmask: 255.255.255.0, DHCP client If this address conflicts or does not match with your network, it must be change...

Page 5 - Connecting to the PC’s Console port; Changing the IP address; Saving the IP address

IPLink 2884/2888 Quick Start Guide 5 2.3 Connecting to the PC and logging in via the Console port 1. To access the OnSite configuration via the console port, connect the DB9-RJ45 adapter to the DB-9 serial port on the PC or dumb terminal. Use the RJ45 straight-through cable between the adapter and t...

Page 6 - The 2888 comes with either two or four T1/E1 ports.; Connecting the T1/E1 ports; To connect the twisted pair cable to the T1/E1 port:; Additional information; OnSite Model 2888 User Manual

6 OnSite 2888 Quick Start Guide 3.0 Connecting the T1/E1 ports The 2888 comes with either two or four T1/E1 ports. Figure 5. Connecting the T1/E1 ports To connect the twisted pair cable to the T1/E1 port: 1. Attach the male connector of the twisted pair cable to the female connector on the OnSite. 2...

Page 7 - A.0 Compliance Information; A.2 CE Declaration of Conformity; The signed Declaration of Conformity can be downloaded from; A.3 Authorized European Representative

IPLink 2884/2888 Quick Start Guide 7 A.0 Compliance Information A.1 Compliance EMC: • FCC Part 15, Class A • EN55022, Class A • EN55024 Safety: • UL 60950-1/CSA C22.2 N0. 60950-1 • IEC/EN60950-1 • AS/NZS 60950-1 PSTN Regulatory: • FCC Part 68 • CS-03 • TBR 12 & 13 (E1) • AS/ACIF S016:2001 (E1) A...

Page 8 - Copyright statement; OnSite; Patton support headquarters in the USA; Note; Warranty, Compliance Information

8 OnSite 2888 Quick Start Guide Copyright statement Copyright © 2012, Patton Electronics Company. All rights reserved.The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document. Trademarks statement The te...