Nilfisk ALTO MS Series - Manual

Page 2 - SAFETY INSTRUCTIONS; Service Assistance; C A U T I O N; R I S K O F E L E C T R I C S H O C K

1 SAFETY INSTRUCTIONS 1. Read Instructions All the safety and operation instructions should be read before using the product and retain them for future reference. 2. Water & Moisture This product should not be used near water and will be protect from atmospheric agents in fixed or temporary inst...

Page 3 - TABLE OF CONTENTS

2 TABLE OF CONTENTS 1. INTRODUCTION.......................................................................................................................................................3 2. FEATURES........................................................................................................

Page 6 - and the other side to the INPUT socket of your speaker cabinet.

QUICK START MS Passive Full-range Speakers Stereo Power Amplifier speaker cable TripodMount Left Main Mix Output Right Main MixOutput Mixer TripodMount speaker cable 5 3 . QUICK START Make all initial connections with all the equipment powered off, and ensure that all the main volume controls aretur...

Page 7 - QUICK START

6 -. For Passive Subwoofer & Satellite Speakers 1). Connect one side of speaker cable to the Output CHA/CHB or Binding Post of your stereo power amplifier and the other side to the Input socket of your subwoofer, with the second speaker cable connect the Output of the subwoofer to the Input of s...

Page 8 - - PASSIVE SUBWOOFER Speaker for MS15S / MS18S

7 4. CONTROL ELEMENTS 4.1MS SERIES CABINET - PASSIVE FULL-RANGE Speaker for MS12 / MS15 / MS152 / MS153/MS154 (1) INPUT: Receive the power coming from an external power amplifier (SPK +1/-1 connected; +2/-2 not connected). (2) THRU: Direct LINK for connect in parallel a second speaker cabinet (SPK +...

Page 9 - LTO MS1 SPEAKER MODELLER; This control adjusts the input gain by a range of -20 dB to +20dB.; FLAT; THE REAR PANEL; power amplifier inputs; Input Connector; POWER; LEFT

8 4.2 LTO MS1 SPEAKER MODELLER - THE FRONT PANEL 1. Gain Control This control adjusts the input gain by a range of -20 dB to +20dB. 2. Clip LED This LED lights up when the input signal is too strong. It warns that the output signal may cause distortion. Please attenuate the level of the input signal...

Page 10 - INSTALLATION AND CONNECTION; For MS Series Cabinets; Sleeve

9 5. INSTALLATION AND CONNECTION 5.1 For MS Series Cabinets Please use only the power connectors to make connections with other signal source equipment for the MS seriescabinets. The power connector has four terminals: 1+, 1-, 2+, 2-. In our cabinets, only 1+/1- are used to connect the Speaker+/Spea...

Page 11 - TECHNICAL SPECIFICATION; MS1 SPEAKER TECHNICAL SPECIFICATION; Model Item

1 0 6. TECHNICAL SPECIFICATION 6.1 MS1 SPEAKER TECHNICAL SPECIFICATION Model Item MS12 MS15 2-way vented box 200Watt AES Standard 400Watt Peak 119dB SPL calculated 65Hz / 20kHz at -10dB 8 Ohm 2k5Hz / 12dB/Oct Electronic Dynamic Protection 12" woofer / 2" voice coil 1" Neodymium Driver / ...

Page 14 - manual without written permission is forbidden. Copyright; SE KAKU TECHNICAL GROUP LIMITED

No. 1, Lane 17, Sec. 2, Han Shi West Road, Taichung 40151 Taiwan http://www.altoproaudio.com Tel: 886-4-22313737 email: [email protected] Fax: 886-4-22346757 c All rights reserved to ALTO. All features and content might be changed without prior notice. Any photocopy, translation, or reproduction...

Nilfisk ALTO MS Series - Manual

Table of Contents:

Summary

Other Nilfisk ALTO Models