Nilfisk ALTO DPA6000 - Manual

Page 2 - SAFETY RELATED SYMBOLS; IMPORTANT SAFETY INSTRUCTIONS

SAFETY RELATED SYMBOLS C A U T I O N R I S K O F E L E C T R I C S H O C K D O N O T O P E N This symbol, wherever used, alerts you to the pre-sence of un-insulated and dangerous voltages with-in the product enclosure. These are voltages thatmay be sufficient to constitute the risk of electricshock ...

Page 3 - PREFACE

2 PREFACE Dear Customer: For LTO AUDIO TEAM, music and audio are much more than a job, they are a passion and an obsession! By purchasing our LTO products you become the most important member of our LTO AUDIO TEAM. We would like to share with you our passion for what we design and we invite you to m...

Page 4 - TABLE OF CONTENTS; WORKING WETH PRESETS; APPLICATION; TECHNICAL SPECIFICATIONS

TABLE OF CONTENTS 1. INTRODUCTION .....................................................................................................................................4 2. FEATURES ..........................................................................................................................

Page 7 - Input Connector; Input Connector

RS485 IN RS485 OUT RS232 SERIAL PROT CH1 BALANCED INPUT PARALLEL OUTPUT CH2 BALANCED INPUT PARALLEL OUTPUT SERIAL MODEL 1 + 1 - POS NEG BRIDGE MONO 2 + 2 - POS NEG 1 + 2 + POS NEG 1 + 1 - POS NEG INPUT INPUT T I P / P I N 2R I N G / P I N 3S L E E V E / P I N 1 T I P / P I N 2R I N G / P I N 3S L E ...

Page 8 - Channel Selection; both selected

4.3 Channel Selection There are total 3 options available (CH1, CH2, CH1+CH2), you can apply these effect settings on either or channels. both selected Select "CHSEL" using SELECT key, the "CHSEL" indicator lights up and the last selected channel will be displayed. Use UP or DOWN key...

Page 9 - RECALL; . The new setup is now saved as a; Maxi Editor File; FILE; OK

11 6. PARAMETER MENUS DESCRIPTION - HUM CANCEL: allows the modification of the dynamic NOTCH filter parameters. The graph included shows the filter response curve. - NOISE GATE: allows the modification of the noise gate parameters. The graph included shows the filter curve. - MULTICOMP: allows the m...

Page 10 - If your; DPA unit; Ganging

2>. The PC Editor should now load. A welcome screen will appear. This closes after 5 seconds (or click on it). Select NEW from the FILE menu. A window will open showing several different model names, becausethe same software is used for some of our pro audio models. Select DPA amp and click OK.Yo...

Page 11 - Introduction to the PC Editor; form

10 5.5 Help File The HELP file accessible from within the PC Editor will be updated as necessary. Since software updates after theprinting of this manual may affect the instructions provided here, please check the Help File for any later remarks. 5.6 Introduction to the PC Editor When you launch the...

Page 12 - First Steps with the PC Editor

5.3 First Steps with the PC Editor To avoid accidentally overwriting an existing PRESET, it is important that you follow the correct routine when ini-tiating a session between the DPA unit and your computer. RS485 IN RS485 OUT RS232 SERIAL PROT CH1 BALANCED INPUT PARALLEL OUTPUT CH2 BALANCED INPUT P...

Page 13 - The wire must be changed between 2,3 pin.; Special attentions for R 232 interface:; G R O U N D; BALANCED JACK; Parsllel Output Connectors, RS485 OUT; GROUND

1 2 RS232 RS232 (9Pin-F) PIN 5 PIN 3 PIN 2 (RXD) PIN3(GND) PIN5 (TXD) PIN2 PIN 3(RXD)PIN 2(TXD)PIN 5(GND) The wire must be changed between 2,3 pin. 9 PIN 9 PIN Special attentions for R 232 interface: S 1. Be careful not to use the pin-to-pin cable in the system, it may damage the communication part ...

Page 14 - RS232 Serial Communication Port

channel 1 or 2 will be output from both channel 1 and 2 simultaneously. Details refer to the chapter 9. - Bridge Mode In this mode, the signal input into channel 1 will be output from the bridged end, on the other hand, theoutput level control of channel 2 should be turned down to smallest.Details r...

Page 18 - TECHNICAL SPECIFICATIONS

1 7 10. TECHNICAL SPECIFICATIONS MODEL 8 o h m s p e r c h a n n e l ( E I A J ) 4 ohms per channel(EIAJ) 8 ohms, 1KHz, 0.1%THD Bridge Mono Mode Distortion (SMPTE-IM) Frequency Response Damping Factor, 1 kHz and below Signal to Noise,20Hz-20KHz Voltage Gain Input Sensitivity @ 4 ohms Input Clipping ...

Page 19 - LTO

1 8 11. WARRANTY 1. WARRANTY REGISTRATION CARD To obtain Warranty Service, the buyer should first fill out and return the enclosed Warranty Registration Card within10 days of the Purchase Date. All the information presented in this Warranty Registration Card gives the manufacturer a better understan...

Page 20 - manual without written permission is forbidden. Copyright; SEIKAKU TECHNICAL GROUP LIMITED

SEKAKU ELECTRON INDUSTRY (H.K.) CO., LTD. No. 1, Lane 17, Sec. 2, Han Shi West Road, Taichung 40151, Taiwan http://www.altoproaudio.com Tel: 886-4-22313737 email: [email protected] Fax: 886-4-22346757 c All rights reserved to ALTO. All features and content might be changed without prior notice. ...

Nilfisk ALTO DPA6000 - Manual

Table of Contents:

Summary

Other Nilfisk ALTO Models