National Instruments NI 5422 - Manual
National Instruments NI 5422 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – Amplitude and Offset
- Page 5 – Frequency and Transient Response
- Page 8 – Specification
- Page 15 – Sample Clock
- Page 16 – Sample Rate Range and Resolution; Sample Clock Delay Range and Resolution
- Page 17 – System Phase Noise and Jitter (10 MHz Carrier)
- Page 18 – Onboard Clock
- Page 19 – CLK IN; (Sample Clock and Reference Clock Input, Front Panel Connector)
- Page 20 – PFI 0 and PFI 1
- Page 22 – Optional Front Panel Connector
- Page 23 – Output Signal Characteristics (Continued)
- Page 24 – Start Trigger
- Page 25 – Markers
- Page 27 – Arbitrary Waveform Generation Mode
- Page 29 – Calibration
- Page 30 – Power
- Page 31 – Software
- Page 32 – Environment; Specifications
- Page 34 – Notes
- Page 35 – Physical
- Page 36 – Where to Go for Support
NI 5422 Specifications
NI PXI-5422 16-Bit 200 MS/s Arbitrary Waveform Generator
Unless otherwise noted, the following conditions were used for each
specification:
•
Analog Filter enabled.
•
Signals terminated with 50
Ω
.
•
Direct Path set to 1 V
pk-pk
, Low-Gain Amplifier Path set to 2 V
pk-pk
,
and High-Gain Amplifier Path set to 12 V
pk-pk
.
•
Sample rate set to 200 MS/s and the Sample Clock Source set to
Divide-by-
N
.
Typical values are representative of an average unit operating at room
temperature (20 °C ± 3 °C). Specifications are subject to change without
notice. For the most recent NI 5422 specifications, visit
ni.com/manuals
.
To access all of the NI 5422 documentation, including the
NI Signal
Generators Getting Started Guide
, which contains functional descriptions
of the NI 5422 signals, navigate to
Start»Programs»National
Instruments»NI-FGEN»Documentation
.
Hot Surface
If the NI 5422 has been in use, it may exceed safe handling temperatures and
cause burns. Allow the NI 5422 to cool before removing it from the chassis.
Contents
CH 0 ........................................................................................................ 2
Sample Clock .......................................................................................... 15
Onboard Clock ........................................................................................ 18
Phase-Locked Loop (PLL) Reference Clock .......................................... 18
CLK IN ................................................................................................... 19
PFI 0 and PFI 1 ....................................................................................... 20
DIGITAL DATA & CONTROL (DDC) ................................................ 22
Start Trigger ............................................................................................ 24
Markers ................................................................................................... 25
Arbitrary Waveform Generation Mode................................................... 27
Calibration............................................................................................... 29
Power ...................................................................................................... 30
Software .................................................................................................. 31
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
© National Instruments Corporation 3 NI 5422 Specifications Amplitude and Offset Amplitude Range Path Load Amplitude (V pk-pk ) 1. Amplitude values assume the full scale of the DAC is utilized. If an amplitude smaller than the minimum value is desired, then waveforms less than full scale of the DAC ...
© National Instruments Corporation 5 NI 5422 Specifications Output Characteristics (Continued) Output Enable Software-selectable. When the Output Path is disabled, the CH 0 Output is terminated to ground with a 1 W resistor equal to the selected output impedance. — Maximum Output Overload The CH 0 o...
NI 5422 Specifications 8 ni.com Figure 5. Recommended Sine Wave Frequency Versus Amplitude Table 1. (Continued) Specification Value Comments Suggested Maximum Frequencies for Common Functions Function Path Disable the Analog Filter for square, ramp, and triangle functions. Direct Low-Gain Amplifier ...
