National Instruments 321042A-01 - Manual

National Instruments 321042A-01

National Instruments 321042A-01 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
Page: / 53

Table of Contents:

  • Page 3 – Limited Warranty; . This limitation of the liability of National Instruments will
  • Page 4 – LabVIEW; WARNING REGARDING MEDICAL AND CLINICAL
  • Page 5 – FCC/DOC Radio Frequency Interference Compliance; Federal Communications Commission
  • Page 6 – Reorient or relocate the receiver’s antenna.
  • Page 7 – Contents; About This Manual
  • Page 8 – Glossary; Electrical
  • Page 9 – How to Use the Manual Set
  • Page 10 – Organization of This Manual; This manual is organized as follows:; Conventions Used in This Manual; The following conventions are used in this manual.; bold; italic
  • Page 11 – bold monospace; IEEE 488 and IEEE 488.2 refer to the ANSI/IEEE Standard; Related Documentation; Microsoft Windows User's Guide, Microsoft Corporation
  • Page 12 – Customer Communication
  • Page 13 – © National Instruments Corp.; How to Use This Manual
  • Page 14 – What You Need to Get Started; STD-GP IB feedthrough front panel assembly; Hardware Description
  • Page 15 – Software Description; ni-pnp Utility Overview; Optional Programming Environments
  • Page 16 – Characteristic; DMA Channel
  • Page 17 – Install the Hardware; Perform the following steps to install the STD-GPIB.
  • Page 18 – Power on your system.
  • Page 19 – Configure the Hardware; If you want to use interrupts for the STD-GPIB
  • Page 21 – Selecting the Base I/O Address; Switch Setting
  • Page 24 – Selecting the Interrupt Request Line
  • Page 27 – Figure 2-7. Jumper Setting for Disabling Interrupts; Selecting the DMA Channel
  • Page 29 – Using Programmed I/O for GPIB Transfers; Figure 2-9. DMA Jumper Setting for No DMA Channel; Setting the Shield Ground Configuration
  • Page 30 – Figure 2-10. Ground Configuration Jumper Settings; Setting the Operating Mode
  • Page 32 – Install the Software
  • Page 33 – Configure the Software
  • Page 35 – Troubleshooting ni-pnp Error Messages
  • Page 36 – Run the Hardware Diagnostic Test; Troubleshooting Hardware Diagnostic Test Error Messages; Using Single-Cycle DMA
  • Page 37 – Correcting Hardware Settings; Make sure you are using a valid base I/O address.
  • Page 38 – Run the Software Diagnostic Test; Follow these steps to run the Software Diagnostic Test:; Troubleshooting Software Diagnostic Test Error Messages; In the following paragraphs,
  • Page 39 – Presence Test of Software Components; Presence Test of Driver; gpib
  • Page 40 – GPIB Cables Connected; Disconnect all GPIB cables before trying the test again.; Common Questions
  • Page 41 – What should I do if one of the diagnostic tests fails with an error?
  • Page 42 – Introduction to the Win16 Interactive Control Utility; Verify GPIB communication with your device quickly and easily.; General Programming Considerations; You must include the header file in your source code.
  • Page 44 – Frontplane Interrupts; Pin
  • Page 45 – Backplane Interrupts; The interrupt routing for the STD-GPIB is shown in Table B-2.
  • Page 46 – Branch Offices
  • Page 47 – Technical Support Form
  • Page 51 – Documentation Comment Form
  • Page 53 – Prefix
Loading the manual

© Copyright 1995 National Instruments Corporation.

All Rights Reserved.

Getting Started with Your STD-GPIB and the

NI-488.2

™

Software for Windows

December 1995 Edition

Part Number 321042A-01

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Limited Warranty; . This limitation of the liability of National Instruments will

Limited Warranty The STD-GPIB hardware is warranted against defects in materials and workmanship fora period of two years from the date of shipment, as evidenced by receipts or otherdocumentation. National Instruments will, at its option, repair or replace equipment thatproves to be defective during...

Page 4 - LabVIEW; WARNING REGARDING MEDICAL AND CLINICAL

Copyright Under the copyright laws, this publication may not be reproduced or transmitted in anyform, electronic or mechanical, including photocopying, recording, storing in aninformation retrieval system, or translating, in whole or in part, without the prior writtenconsent of National Instruments ...

Page 5 - FCC/DOC Radio Frequency Interference Compliance; Federal Communications Commission

FCC/DOC Radio Frequency Interference Compliance This equipment generates and uses radio frequency energy and, if not installed and usedin strict accordance with the instructions in this manual, may cause interference to radioand television reception. This equipment has been tested and found to compl...

Other National Instruments Models

All National Instruments Other