National Instruments 12-Bit 200 MS/s Digitizer - Manual
National Instruments 12-Bit 200 MS/s Digitizer – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Vertical; Specification
- Page 3 – Voltage Levels; Accuracy
- Page 13 – Horizontal; Sample Clock
- Page 15 – External Sample Clock
- Page 17 – Trigger
- Page 21 – TClk Specifications
- Page 22 – Waveform Specifications
- Page 23 – Calibration
- Page 24 – Software
- Page 25 – Environment
- Page 27 – Safety; CE Compliance
- Page 28 – Environmental Management; Waste Electrical and Electronic Equipment (WEEE); Physical; Front Panel Connectors; ⬉ᄤֵᙃѻક∵ᵻࠊᄣ⧚ࡲ⊩ ˄Ё; RoHS
- Page 29 – Dimensions and Weight; NI PXI-5124 Front Panel Indicators
- Page 31 – Where to Go for Support
NI PXI/PCI-5124 Specifications
12-Bit 200 MS/s Digitizer
This document lists the specifications for the NI PXI/PCI-5124 (NI 5124)
high-speed digitizer. Unless otherwise noted, these specifications are valid
for the following conditions:
•
All filter settings
•
All impedance selections
•
Sample clock set to 200 MS/s using onboard clock
Typical values are representative of an average unit operating at room
temperature. Specifications are subject to change without notice. For the
most recent NI 5124 specifications, visit
ni.com/manuals
.
To access the NI 5124 documentation, including the
NI High-Speed
Digitizers Getting Started Guide
, which contains functional descriptions
of the NI 5124 signals, navigate to
Start»All Programs»National
Instruments»NI-SCOPE»Documentation
.
Hot Surface
If the NI 5124 has been in use, it may exceed safe handling temperatures and
cause burns. Allow the NI 5124 to cool before removing it from the PXI chassis or PC.
Refer to the
section for operating temperatures of this device.
Contents
Analog Input (Channel 0 and Channel 1) ........................................ 2
Sample Clock ................................................................................... 13
Phase-Locked Loop (PLL) Reference Clock ................................... 16
CLK IN (Sample Clock and Reference Clock Input,
Front Panel Connector) ................................................................. 17
CLK OUT (Sample Clock and Reference Clock Output,
Front Panel Connector) ................................................................. 17
Reference (Stop) Trigger ................................................................. 17
TRIG (External Trigger, Front Panel Connector) ............................ 19
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
NI PXI/PCI-5124 Specifications 2 ni.com PFI 0 and PFI 1 (Programmable Function Interface, AUX Front Panel Connector) ...............................................................20 TClk Specifications .................................................................................21Waveform Speci...
© National Instruments Corporation 3 NI PXI/PCI-5124 Specifications Voltage Levels Full Scale (FS) Input Range and Programmable Vertical Offset 50 Ω 1 M Ω — Range (V pk-pk ) Vertical Offset Range (V) Range (V pk-pk ) Vertical Offset Range (V) 0.2 ±0.1 0.2 ±0.1 0.4 ±0.2 0.4 ±0.2 1 ±0.5 1 ±0.5 2 ±1 2 ...
© National Instruments Corporation 13 NI PXI/PCI-5124 Specifications Horizontal Sample Clock Specification Value Comments Sources NI PXI-5124 NI PCI-5124 * Internal Sample Clock is locked to the Reference Clock or derived from the onboard VCXO Internal, Onboard Clock (internal VCXO) * External, CLK ...
