Miele DA 219-2 EXT - Manual

The appliance is only completelyisolated from the electricity supply when: – it is switched off at the wall socket and the plug removed. (Do not pullon the cable, only on the plug), or – the fuse from the fused spur connec- tion unit is withdrawn or, – the mains fuse is withdrawn, or – the screw-out...

Installation The distance between the top ofthe cooker/hob and the bottom of the cooker hood must measure at least: – 450 mm above electric hobs and cookers – 650 mm above gas hobs and cookers – 650 mm above an open grill from our range When fitted above an open grill thecooker hood must not be used...

When using the cooker hood inextraction mode at the same time as another heating appliance which de-pends on the air in the room, (e.g. gas,oil or coal fired heaters, continuous flowor other water heaters, gas cooker, gashob or gas oven) special care must betaken, as the action of the cooker hoodext...

Description of the appliance Description of the appliance 8

Functional description The cooker hood works with . . . air extraction The air is drawn in and cleaned by thegrease filters and directed outside. The cooker hood is fitted with a non-return flap . This flap is closed when the cookerhood is switched off. No exchange ofroom air and outside air can tak...

Operation Main switch Switch the main switch to "I". The fanand the lighting can now be operated. If the appliance is not going to be usedfor a longer period of time (e.g. whilston holiday) switch the appliance off byturning the main switch to "0". The next time it is switched on the...

To switch the fan off Press the On/Off touch control toswitch the fan off. The indicator lamp above the controlgoes out. Switching the lighting on The hob lighting can be switched onand off independently of the fan. Briefly press the lighting touch con- trol to switch on the hob illumination. The in...

Filter operating hours counter The number of hours the appliance hasbeen in operation for is stored in mem-ory. The indicator lamp above the grease fil-ter control will light up after 30 hours ofoperation. The grease filters must thenbe cleaned. After the grease filters have beencleaned and put back...

Setting/altering the active charcoalfilter operating hours counter The active charcoal filters are onlyused for cooker hoods which are setup for recirculation mode. They are not required for vented extraction. On delivery the operating hourscounter for the active charcoal filters isset to unlimited ...

Cleaning and care Before any cleaning or maintenancework the cooker hood must be dis-connected from the mains supply.Ensure that:– it is switched off at the wall socketand the plug has been withdrawn(do not pull on the cable, only onthe plug), or– the fuse has been withdrawn fromthe fused spur conne...

Grease filters Re-usable metal filters are fitted whichremove solid particles (oil, dust, etc.)from the kitchen vapours, preventingsoiling of the cooker hood. The filters should be cleaned regularly(at least every 3-4 weeks) to avoid abuild-up of fat, but always clean assoon as the grease filter tou...

Changing a light tube Disconnect the cooker hood fromthe mains supply. Ensure that:– it is switched off at the wall socketand the plug has been withdrawn(do not pull on the cable, only onthe plug), or– the fuse has been withdrawn fromthe fused spur connection unit, or– the mains fuse is withdrawn; o...

Retaining plates There are three retaining plates A, Band C for fixing the cooker hood to thewall. First of all drill the holes for attachingthe canopy and for fitting retainingplate A. Before fitting the retaining plate drawa vertical line centrally above thehob on the back wall. Mark measurement S...

At a maximum distance of 365 mmfrom the ceiling, hold retaining plateC against the wall and use the not-ches to align it with the middle line.Mark the two drill holes. Drill two 8 mm ø holes into the walland press the S8 plugs into theholes. Screw on retaining plate C with two5 x 40 mm screws. Canop...

Motor unit (not when operating the external fan) with air extractionIf a non-return flap is not present inthe venting system, the non-return flap supplied must be fitted into the exhaust connection in the motor unit.The flaps must open upwards. The cooker hood is designed to takeø 150 mm exhaust duc...

For appliances connected to an ex-ternal fan, model designation...EXT: Connect the control unit and the ex-ternal fan with the connection cableand the six pole plug. Connect the appliance to the mainsvia a fused spur or fused socket asappropriate. Before connecting the applianceread the safety notes...

The paper protective sheet protects theextension piece from being scratchedwhen the tower is being fitted. It isremoved when fitting is complete. Fold the protective sheet at the top. Remove the protective foil fromaround the sticking points. Stick the protective sheet to the ex-tension piece so tha...

Connection for air extraction Danger of toxic fumes.Please heed the "Warning andSafety instructions" to avoid thedanger of toxic fumes. The cooker hood should be in-stalled according to local buildingregulations. Seek approval from thebuilding inspector where necessary. – All ducting, pipewo...

Important: If the exhaust ducting is to run throughrooms, ceiling space etc. where theremay be great variations in temperaturebetween the different areas, the prob-lem of sweating or condensation willneed to be addressed. The exhaustducting will need to be suitably insu-lated. Condensate trap In add...

Electrical connection All electrical work should be under-taken by a suitably qualified andcompetent person in strict accord-ance with national and local safetyregulations.Installation, repairs and other workby unqualified persons could bedangerous. The manufacturer cannot be held responsible for un...

Important The wires in the mains lead are col-oured in accordance with the followingcode: Green/yellow = earth Blue = neutral Brown = live If the appliance is to be connected viaa plug and socket, please note the fol-lowing: As the colours of the wires in the mainslead of this appliance may not corr...

After Sales Service In the event of a fault which you cannotcorrect yourself please contact: – Your Miele Dealer or – The Miele Service Department (see back cover for address). When contacting the Service Depart-ment, please quote the model and ser-ial number of your appliance. Theseare shown on the...

Technical data Rated loadDA 216-2, 217-2, 219-2 . . . . . . . 222 W Lighting . . . . . . . . . . . . . . . . . 2 x 11 W VoltageUK, IRL, NZ . . . . . . . . . . . . . . . . . 230 VAUS . . . . . . . . . . . . . . . . . . . . . . . 240 V Frequency . . . . . . . . . . . . . . . . ~ 50 Hz Fuse rating (UK)...