Honeywell RTH8500D- Manual

Honeywell RTH8500D

Honeywell RTH8500D– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
Page: / 64

Table of Contents:

  • Page 2 – Contents
  • Page 3 – Step 1. Prepare for Installation; Check that the following items are included:; WALLPLATE
  • Page 5 – Step 2. Follow Important Instructions; Do not connect the wires to the new thermostat based on wire; OLD THERMOSTAT; RED; DO NOT WIRE
  • Page 6 – Step 3. Remove Old Thermostat; Turn off power at the heating and/or cooling system or; MERCURY NOTICE
  • Page 7 – Step 4. Follow Special Instructions; two; WIRE HOLE
  • Page 8 – If you have only; one; C and/or C1 wire connected to your old
  • Page 10 – Step 5. Label Old Thermostat Wires; RC
  • Page 11 – Step 6. Mount New Wallplate to Wall; Separate the wallplate from the thermostat as shown.
  • Page 12 – Pass the labeled wires through the wire hole on the wallplate.; WALL OPENING
  • Page 15 – Step 7. Connect Wires to New Wallplate; CONVENTIONAL; SCREW TERMINALS
  • Page 19 – Be sure to read the note referenced in the numbered; HEAT PUMP
  • Page 20 – Leave metal jumper wire between RC and R in place.; NOTES FOR HEAT PUMP SYSTEMS
  • Page 21 – Push excess wire back into the wall opening. Keep wires in the
  • Page 22 – Step 8. Install Batteries; Install three fresh AAA alkaline batteries on the back of the; BACK OF THERMOSTAT
  • Page 23 – Step 9. Attach New Thermostat to Wallplate; Align the screw blocks with the pins on the back of the; PINS ON
  • Page 24 – Step 10. Set the Calendar; day in memory for up to ten years, under normal use, once the
  • Page 25 – Use the arrow keys to set the current time.
  • Page 26 – Step 11. Configure Installer Setup; Use the Installer Setup Menu to match your new thermostat to
  • Page 28 – Date; Installer
  • Page 29 – - Multistage Heat Pumps
  • Page 30 – Fan Control
  • Page 31 – Heat Pump
  • Page 32 – Heating
  • Page 33 – Temperature
  • Page 34 – not adjust for Daylight Savings Time.
  • Page 36 – Adaptive
  • Page 37 – Clock
  • Page 40 – Heat
  • Page 41 – Set Fan Setting; Press the Fan button to select Auto or On:; Auto; —Normal setting for most homes. The fan runs only; On; —The fan runs continuously. Use this setting for
  • Page 43 – Program Your Heating and Cooling Schedule (Cont); OK TO PICK MULTIPLE DAYS
  • Page 44 – OK
  • Page 45 – When complete, press Done key. “Saving Changes” appears on; SAVING
  • Page 46 – Cancel a Schedule Period
  • Page 47 – Use the arrows to set the current time.
  • Page 48 – Set Temperature Overrides
  • Page 49 – Permanent Hold
  • Page 50 – Vacation Hold
  • Page 51 – Clean Your Thermostat Screen; OK TO
  • Page 52 – CHANGE FILTER; OK TO PICK MULTIPLE DAYS SCREEN LOCKED
  • Page 53 – Understanding Temperature Recovery Feature
  • Page 54 – Replace Batteries; When the LO Battery indicator is flashing, replace the
  • Page 55 – Remove the old batteries and insert three fresh AAA alkaline
  • Page 57 – Review Battery Tips
  • Page 58 – Built-in Compressor Protection
  • Page 59 – Troubleshooting Tips
  • Page 62 – Customer Assistance; For assistance with your Honeywell product, please visit
  • Page 63 – Limited One-Year Warranty; write Retail Products
  • Page 64 – Automation and Control Solutions; Honeywell International Inc.
Loading the manual

OWNER’S GUIDE

U.S. Pat. 6,595,430
Other Patents Pending
® U.S. Registered Trademark
© 2004 Honeywell International Inc.
All Rights Reserved

69-1725-1

RTH8500D Touch Screen

Programmable Thermostat

The RTH8500D Thermostat provides electronic control of 24 Vac heating and
cooling systems or 750 mV heating systems.

For assistance with your Honeywell product, please visit
www.honeywell.com/yourhome or call Honeywell Customer Care
toll free at 1-800-468-1502.

Read and Save these Instructions

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Other Manuals for Honeywell RTH8500D

Summary

Page 2 - Contents

69-1725-1 2 Contents Prepare for Installation................................................................... 3 Follow Important Instructions ......................................................... 5 Remove Old Thermostat................................................................ 6 Follow ...

Page 3 - Step 1. Prepare for Installation; Check that the following items are included:; WALLPLATE

3 69-1725-1 Step 1. Prepare for Installation 1. Check that the following items are included: If any of the items shown above are missing, call Honeywell Customer Care at 1-800-468-1502 before returning the thermostat to the store. CAUTION TURN OFF POWER to system at the furnace, or at the fuse/circu...

Page 5 - Step 2. Follow Important Instructions; Do not connect the wires to the new thermostat based on wire; OLD THERMOSTAT; RED; DO NOT WIRE

5 69-1725-1 Step 2. Follow Important Instructions 1. Do not connect the wires to the new thermostat based on wire color because damage can occur to the heating and/or cooling system. These Installation Instructions explain later how to use the enclosed wire labels to correctly mark the wires connect...

Other Honeywell Models