Honeywell 1533 - Manual
This installation manual covers the Trend T-PI PRT insertion temperature sensor, focusing on its mounting, environmental requirements, and integration with controllers. The document outlines key specifications such as IP67/NEMA6 protection ratings, suitable for immersion or duct applications under controlled humidity and temperature conditions while avoiding corrosive environments. Installation methods include pocket-based, universal-fixing kit, and compression-fitting approaches, each requiring specific tools like threaded bosses or hexagonal keys. The manual also details wiring connections to controllers (e.g., IQ4/IQ3 series), sensor scaling configurations, and testing procedures for accurate operation. Maintenance instructions emphasize proper cleaning under power-off conditions and compliance with WEEE Directive disposal protocols.
Table of Contents:
- Page 1 – Sensor Box Contents and Dimensional Specifications
- Page 2 – Environmental Requirements and Mounting Guidelines
- Page 3 – Immersion Sensor Installation Methods
- Page 4 – Duct Sensor Mounting Procedures
- Page 5 – Sensor Wiring and Assembly Procedure
- Page 6 – Controller Configuration and Operational Testing
- Page 7 – Maintenance and Disposal Instructions
- Page 8 – Publication Details and Contact Information
T-PI PRT Insertion Temperature Sensor Installation Instructions TG201420 Issue 2, 19-Feb-2020 1
Installation Instructions
T-PI
PRT Insertion Temperature Sensor
Important: Retain these instructions
These instructions shall be used by trained service
personnel only.
If the equipment is used in a manner not
specified by these instructions, the protection provided by the
equipment may be impaired.
https://partners.trendcontrols.com
1
Dimensions
2 INSTALLATION
1
BOX CONTENTS
T-PI
Installation Instructions
(TG201420)
Pockets for use as immersion sensor; Brass (WB150) Stainless Steel (WS150)
6 m
m (
0.
24
”)
T-PI-L 300 mm (11.81”)
11
3 m
m (
4.
45
”)
57 mm (2.24”)
135 mm (5.31”)
14 mm (0.53”)
24 mm
(0.95”)
Ø8 mm
(0.31”)
143 mm (5.63”)
Ø6.5 mm (0.25”)
R½” DIN EN10226
CONTENTS
1
Box Contents .................................................................1
2 Installation .....................................................................1
3
Cleaning and Maintenance ...........................................7
4 Disposal .........................................................................7
T-PI-S 150 mm (5.91”)
97 mm (3.82”)
It is recommended that the installation should comply
with the local electrical safety installation practices (e.g.
HSE Memorandum of Guidance on Electricity at Work
Regulations 1989, USA National Electric Code).
ATTENTION:
Observe precautions for handling
electrostatic sensitive devices.
50 m
m
(1
.9
7”
)
6 mm compression
fitting
3 x 4 mm diam. holes
on a 30 mm (1.18”) PCD
(Pitch Circle Diameter)
Mounting flange for use as duct sensor (ACC/DF)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Was this manual helpful?
About this manual
- Brand
- Honeywell
- Model
- 1533
- Document type
- Manual
- Language(s)
- English
- Pages
- 8
- File size
- 859.9 KB
- Format
Other Manuals for Honeywell 1533
Summary
Details regarding the contents of the box, dimensional drawings for installation, and specifications for various sensor types and mounting components.
Mounting guidelines covering environmental conditions, protection ratings (IP67, NEMA6), and specific considerations for immersion and duct applications, including flow conditions.
Step-by-step instructions for mounting an immersion sensor using three methods: installing a new pocket, inserting into a compatible pocket, or using a universal fixing kit, detailing required parts and sealing notes.
