Honeywell IPGSM-4GC- Manual
Honeywell IPGSM-4GC– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – General Information; Package Contents; The installer must inform the central station of this; Operation; ULC Compliance
- Page 4 – STEP 1 – Setup the Customer Account; Have the following information ready:; STEP 2 – Register the Communicator with AlarmNet; IMPORTANT - Do Not mount this device outdoors.; RF Exposure; For this procedure you will need a fully charged 12V battery.
- Page 5 – STEP 4 – Mount and Wire; For ULC compliant installations, refer to the topic on; manual for wiring and component identification.; LED Display Information; ” topic if a wire is detached from its connector.); At this time DO NOT apply power.; Ensure all ground connections are tight.
- Page 6 – PowerBoost1; Ensure the following:
- Page 7 – BATTERY; TRANSFORMER; Tin wire ends
- Page 8 – Wiring the 659EN Line Fault Monitor (Required for ULC); Refer to the installation guide for the 659EN.; Example wiring for an addressable fire control panel:
- Page 9 – STEP 5 – Program the Communicator; You must use the 7720P Programming tool to program the IPGSM-4GC.
- Page 10 – will reset to ensure that the programming features are enabled.; Display; Communicator is not yet initialized.; Setting Factory Defaults; STEP 6 – Configure the Fire Panel
- Page 11 – Dialer Capture Module Information; LED Indicator; Status LED; zzer; RADIO TROUBLE
- Page 12 – PowerBoost1 Information; Missing or low battery.
- Page 13 – Communicator Information; GRN
- Page 14 – RF Specifications; Central Station Messages
- Page 16 – NOTES
- Page 23 – Wiring Diagram
- Page 24 – INDUSTRY CANADA CLASS B STATEMENT; For the latest warranty information, please go to:; Woodbridge, Ontario L4L 7Z4 Canada; Copyright
I
I
P
P
G
G
S
S
M
M
-
-
4
4
G
G
C
C
C
C
o
o
m
m
m
m
e
e
r
r
c
c
i
i
a
a
l
l
F
F
i
i
r
r
e
e
C
C
o
o
m
m
m
m
u
u
n
n
i
i
c
c
a
a
t
t
o
o
r
r
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
a
a
n
n
d
d
S
S
e
e
t
t
u
u
p
p
G
G
u
u
i
i
d
d
e
e
IPGSM-4GC Commercial Fire Comm
unicator
RADIO TROUBLE
LOW BATT
AC ON
AC LOSS
800-12458 7/12 Rev. C
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Honeywell IPGSM-4GC
Summary
IPGSM-4GC Commercial Fire Communicator – Installation and Setup Guide – 1 – General Information The IPGSM-4GC Commercial Fire Communicator (henceforth referred to as IPGSM-4GC) includes everything you need to upgrade a commercial fire system that previously reported by POTS to a system that uses the...
IPGSM-4GC Commercial Fire Communicator – Installation and Setup Guide – 2 – STEP 1 – Setup the Customer Account The communicator requires a subscriber account (customer account) to be setup with AlarmNet Direct. This is accomplished by registering the communicator with AlarmNet. Registering, enables...
IPGSM-4GC Commercial Fire Communicator – Installation and Setup Guide – 3 – 3. Temporarily wire the battery's negative [–] terminal to TB1–4 on the communicator, then wire the battery's plus [+] terminal to TB1–2 on the communicator. Wait about one minute for the communicator to initialize. 4. Posit...
