Honeywell ADVBLE - Manual - manualsarea.com

Page 2 - ADVANCED CONTROLLER - MOUNTING INSTRUCTIONS

ADVANCED CONTROLLER - MOUNTING INSTRUCTIONS 2 31-00553-02 3. DIMENSIONS NOTE: All the dimensions are in inches (mm). For wiring adapter dimension drawing please refer the Comfortpoint Niagara Advanced Plant Controller Product Datasheet -31-00583 and Optimizer Advanced Controller Product Datasheet -3...

Page 3 - MOUNTING PRECAUTIONS; MOUNTING THE CONTROLLER ON

3 ADVANCED CONTROLLER - MOUNTING INSTRUCTIONS 31-00553-02 4. MOUNTING PRECAUTIONS The controllers and wiring adapter support both horizontal and vertical DIN rail mounting on a vertical surface. Do not mount on a horizontal surface. DIN Rail end stop 5. MOUNTING THE CONTROLLER ON A WALL OR PANEL DIN...

Page 4 - MOUNTING THE CONTROLLER ON; Drill Mark

4 ADVANCED CONTROLLER - MOUNTING INSTRUCTIONS 31-00553-02 6. Hold the controller in an orientation such that the red clip is facing downwards and towards the DIN rail. Controller DIN Rail Red Clip 7. Mount the controller onto the DIN rail and push all red clips in to secure it in place. 8. Connect t...

Page 5 - Installing the Push-In Terminal Blocks; Installing the Antennas Remotely (Metal Enclosures)

ADVANCED CONTROLLER - MOUNTING INSTRUCTIONS 5 31-00553-02 10. Insert the screws into the bottom hole and fasten them with a screwdriver. Screw Panel/Wall Controller Anchor 11. Connect the terminal wires, and Ethernet cables. 12. Replace the terminal covers. 13. Replace the Protective Cover if no IO ...

Page 6 - ANTENNA PLACEMENT REMOTE LOCATION; Sur

6 ADVANCED CONTROLLER - MOUNTING INSTRUCTIONS 31-00553-02 Installing the Local Antennas Directly to the Controller (Non-Metal Enclosure) 1. Insert the local antennas into the SMA connectors. 2. Tighten by turning the base of the antenna clockwise. Local Antenna SMA Connector SMA Connector 9. ANTENNA...

Page 7 - MOUNTING THE WIRING; 1 MOUNTING THE PROTECTIVE END

ADVANCED CONTROLLER - MOUNTING INSTRUCTIONS 7 31-00553-02 10. MOUNTING THE WIRING ADAPTER ON THE DIN RAIL NOTE: Use the Wiring Adapter to extend 24 VAC/ VDC power and comms to the next DIN rail or to 24 VAC/VDC power and comms to a remote IO module. 1. Remove the adapter cover by pulling out the cov...

Page 8 - REMOVING THE CONTROLLER

8 ADVANCED CONTROLLER - MOUNTING INSTRUCTIONS 31-00553-02 12. REMOVING THE CONTROLLER FROM THE DIN RAIL 1. Switch off the power supply. 2. Remove the Terminal Covers and Protective Cover if applicable. 3. Disconnect all the controller’s communication and power supply terminals. 4. Hold the controlle...

Page 9 - SPECIFICATIONS OF THE CONTROLLER; IP20 with optional terminal covers; STANDARDS AND APPROVALS; SELV

ADVANCED CONTROLLER - MOUNTING INSTRUCTIONS 9 31-00553-02 SPECIFICATIONS OF THE CONTROLLER POWER CONSUMPTIONCONTROLLER POWER CONSUMPTION CURRENT CONSUMPTION 24 VAC 24 VDC 24 VAC 24 VDC N-ADV-134-H Max. 36 VA Max. 13 W 1500 mA 540 mA N-ADV-133-H-BWA N-ADV-133-H-BWE N-ADV-133-H-BWW Max. 38 VA Max. 14 ...

Page 10 - Electrical Shock Hazard.; WEEE; Electrical and Electronic Equipment Directive; Déclaration d’exposition Attention:

10 ADVANCED CONTROLLER - MOUNTING INSTRUCTIONS 31-00553-02 WARNING Electrical Shock Hazard. Can cause severe injury, death, or property damage. Disconnect the power supply before beginning installation to prevent electrical shock and equipment damage. More than one power supply may have to be discon...

Page 11 - Honeywell | Building Automation; REFERENCE TECHNICAL LITERATURE; TITLE

By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or damages, including attorn...

Honeywell ADVBLE - Manual

Table of Contents:

Other Manuals for Honeywell ADVBLE

Summary

Other Honeywell Models