Honeywell 8712409 - User Manual

Page 2 - Index; INSTALLATION INSTRUCTIONS; Consumer Friendly Message Guide / Programming Record

Page 2 Index INSTALLATION INSTRUCTIONS Package Contents / Tools Required.............................................................Page 1 Prepare Door and Jamb.................................................................................Page 2 Adjusting Deadbolt Latch Set..........................

Page 3 - PACKAGE CONTENTS; DO NOT RETURN TO STORE! If any parts are missing or damaged,

Page 1 INSTALLATION INSTRUCTIONS PACKAGE CONTENTS TOOLS REQUIRED Tools Required for Installation on Pre-drilled Doors:• Phillips Screwdriver Tools Required for Installation on Doors That Require Drilling:• Drill• Tape Measure• Pencil• 2-1/8” (54mm) Drill Hole Saw• 1” (25mm) Drill• 1/16” (2mm) Drill•...

Page 4 - Fold template and place on door 36” (915mm) from; PREPARE DOOR AND JAMB; For Drive in Latch, drill hole size indicated on template and press

Page 2 NOTE: For installation on doors with pre-drilled holes skip to page 4. 1. TEMPLATE a. Cut out template printed on page 15 of this Manual (Figure 1a). b. Fold template and place on door 36” (915mm) from the ground as marked (Figure 1b).2. MARK THE DOOR FOR DRILLING b. Mark center hole on door ...

Page 5 - ADJUSTABLE DEADBOLT LATCH SET

Page 3 ADJUSTABLE DEADBOLT LATCH SET NOTE: Deadbolt Latch Set is shipped with the backset set at 2-3/8” (60mm)Measure the backset (backset is distance between edge of the door and the center of Lock). 1. TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET a. Hold latch with numbers facing...

Page 6 - the latch into the mortise flush. Chisel out excess material if; NOTE: Deadbolt Latch must be retracted when installing; INSTALLING DEADBOLT LATCH SET; OUT SWING DOOR; Deadbolt Latch Extended

Page 4 3. INSTALLING THE DEADBOLT LATCH SET (need phillips head screwdriver) a. Insert Deadbolt Latch Set into door edge hole with the word “UP” and the arrow on the extension plate facing UP. Cross shaped spindle connector will be at the bottom of the Deadbolt Latch Set (Figure 3a). b. Make sure th...

Page 7 - PREPARING THE INTERIOR ASSEMBLY; NOTE: Make sure deadbolt Latch is retracted; Entry Switch; screws to release the Mounting Plate from the Interior Assembly.

Page 5 NOTE: Deadbolt Latch must be retracted when installing NOTE: You are standing outside the door PREPARING THE INTERIOR ASSEMBLY 6. SET THE ENTRY SWITCH FOR LEFT OR RIGHT HANDED DOOR a. Gently move the switch to “L” for Left Handed Door (Figure 6a). b. Gently move the Switch to “R” for Right Ha...

Page 8 - g. Tighten securely with a hand held Phillips Screwdriver.; DO NOT OVER TIGHTEN; during handling and installation.; INSTALLING EXTERIOR ASSEMBLY

Page 6 9. SECURING THE EXTERIOR ASSEMBLY TO THE DOOR a. From the side marked “This side against door”, route the Control Wire through the rectangular slot in the Mounting Plate (Figure 9a). b. Place Mounting Plate against door with tailpiece passing through the center hole in the three hole set (Fig...

Page 9 - INSTALLING INTERIOR ASSEMBLY; the Interior Assembly to the Mounting Plate.; DO NOT OVER TIGHTEN SCREWS; NOTE: Lock and unlock using Interior Knob to see if the

Page 7 INSTALLING INTERIOR ASSEMBLY 11. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY a. Use care to attach the Control Wire male plug to the Interior Assembly female socket connector (Figure 11a). b. Do not force the Control Wire male plug into the Interior Assembly female socket connector (Figu...

Page 10 - INSTALLATION OVERVIEW

Page 8 13. Installing Batteries a. Insert 4 AA high quality Alkaline batteries into the Battery Compartment in the direction noted +/- on the Compartment. The Lock will beep 2 times, the keypad will illuminate blue, and the Honeywell button will flash green twice to signify that it has received powe...

Page 11 - OPERATION INSTRUCTIONS; EXTERIOR ASSEMBLY OVERVIEW; Indicator light; • Indicates Successful Programming Step; Lock button; Factory Settings

Page 9 OPERATION INSTRUCTIONS EXTERIOR ASSEMBLY OVERVIEW Indicator light Green • Indicates Successful Programming Step • Indicates Unlocking is Successful Red • Indicates Failed Programming Step • Indicates Locking is Successful Electronic lock requires (4) High Quality AA Alkaline batteries. When a...

Page 12 - Hear 1 beep and Light Indicator illuminates green.; new Re-enter

Page 10 TO UNLOCK THE LOCKUsing Keypad: Enter a valid User Code (default code is 1234) and press and hear1 beep and lights green. TO LOCK THE LOCKUsing Keypad: Press and then hear 2 beeps and lights red. CHANGE CURRENT OR PRESET PROGRAMING CODEFactory default Programming Code = 123456, this is the m...

Page 13 - To cancel Auto Lock set the time to 00, enter the following:

Page 11 DELETE ONE EXISTING OR PRESET USER CODEThe unit comes with a factory User ID = 01 for User Code = 1234. IMPORTANT: To delete 1 User Code , the lock must have more than 1 User Code in its database. SET OR CANCEL AUTO LOCK You can set the lock to automatically close after each time the lock is...

Page 14 - NOTE: If you only press the; , the system will remain in Vacation Mode.; Hear 1 beep and Light Indicator illuminates green then lock door

Page 12 To reset the lock to the original factory settings including the Programming Code and all User Codes remove one battery for 10 seconds. Reinsert the battery and wait for a long and short beep. Press 3 times within 3 seconds. The lock will beep and the light indicator will turn green. Beeps a...

Page 15 - CONSUMER FRIENDLY MESSAGE GUIDE; My Codes:; PROGRAMMING RECORD

Page 13 NOTE: If you only press the for more than 3 seconds but do not input PC , the system will remain in Vacation Mode. NOTE: When battery is under low voltage, the lock will give the (Low Battery Warning: Beeps and LED flashes red for 5 seconds). During this time your lock can still work. Howeve...

Page 16 - INSTALLATION TROUBLE SHOOTING; Issue; If Correct

Page 14 INSTALLATION TROUBLE SHOOTING Issue Solution Latch Working Backwards- Lock unlocks when lock button is pushed or locks when unlock button or code is pushed. Direction switch is set to incorrect setting. Remove the Interior Assembly and move the switch to the opposite direction. • Check that ...

Page 19 - CONSUMER ASSISTANCE; * Insert correct Country Code

Page 17 CONSUMER ASSISTANCE EMAIL: [email protected] WEBSITE: www.honeywellsafes.com ADDRESS: Consumer Assistance Dept. LH Licensed Products, Inc., 860 East Sandhill Avenue Carson, CA 90746 USA TELEPHONE: US/Canada 1-877-354-5457 (Toll Free) Mexico 01-800-288-2872 After English voice recording stops...

Honeywell 8712409 - User Manual

Table of Contents:

Summary

Other Honeywell Models