Honeywell 8712409 - Manuals

Page 3 ADJUSTABLE DEADBOLT LATCH SET NOTE: Deadbolt Latch Set is shipped with the backset set at 2-3/8” (60mm)Measure the backset (backset is distance between edge of the door and the center of Lock). 1. TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET a. Hold latch with numbers facing...

Page 4 3. INSTALLING THE DEADBOLT LATCH SET (need phillips head screwdriver) a. Insert Deadbolt Latch Set into door edge hole with the word “UP” and the arrow on the extension plate facing UP. Cross shaped spindle connector will be at the bottom of the Deadbolt Latch Set (Figure 3a). b. Make sure th...

Page 5 NOTE: Deadbolt Latch must be retracted when installing NOTE: You are standing outside the door PREPARING THE INTERIOR ASSEMBLY 6. SET THE ENTRY SWITCH FOR LEFT OR RIGHT HANDED DOOR a. Gently move the switch to “L” for Left Handed Door (Figure 6a). b. Gently move the Switch to “R” for Right Ha...

Page 6 9. SECURING THE EXTERIOR ASSEMBLY TO THE DOOR a. From the side marked “This side against door”, route the Control Wire through the rectangular slot in the Mounting Plate (Figure 9a). b. Place Mounting Plate against door with tailpiece passing through the center hole in the three hole set (Fig...

Page 7 INSTALLING INTERIOR ASSEMBLY 11. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY a. Use care to attach the Control Wire male plug to the Interior Assembly female socket connector (Figure 11a). b. Do not force the Control Wire male plug into the Interior Assembly female socket connector (Figu...

Page 8 13. Installing Batteries a. Insert 4 AA high quality Alkaline batteries into the Battery Compartment in the direction noted +/- on the Compartment. The Lock will beep 2 times, the keypad will illuminate blue, and the Honeywell button will flash green twice to signify that it has received powe...

Page 9 OPERATION INSTRUCTIONS EXTERIOR ASSEMBLY OVERVIEW Indicator light Green • Indicates Successful Programming Step • Indicates Unlocking is Successful Red • Indicates Failed Programming Step • Indicates Locking is Successful Electronic lock requires (4) High Quality AA Alkaline batteries. When a...

Page 10 TO UNLOCK THE LOCKUsing Keypad: Enter a valid User Code (default code is 1234) and press and hear1 beep and lights green. TO LOCK THE LOCKUsing Keypad: Press and then hear 2 beeps and lights red. CHANGE CURRENT OR PRESET PROGRAMING CODEFactory default Programming Code = 123456, this is the m...

Page 11 DELETE ONE EXISTING OR PRESET USER CODEThe unit comes with a factory User ID = 01 for User Code = 1234. IMPORTANT: To delete 1 User Code , the lock must have more than 1 User Code in its database. SET OR CANCEL AUTO LOCK You can set the lock to automatically close after each time the lock is...

Page 12 To reset the lock to the original factory settings including the Programming Code and all User Codes remove one battery for 10 seconds. Reinsert the battery and wait for a long and short beep. Press 3 times within 3 seconds. The lock will beep and the light indicator will turn green. Beeps a...

Page 13 NOTE: If you only press the for more than 3 seconds but do not input PC , the system will remain in Vacation Mode. NOTE: When battery is under low voltage, the lock will give the (Low Battery Warning: Beeps and LED flashes red for 5 seconds). During this time your lock can still work. Howeve...

Page 14 INSTALLATION TROUBLE SHOOTING Issue Solution Latch Working Backwards- Lock unlocks when lock button is pushed or locks when unlock button or code is pushed. Direction switch is set to incorrect setting. Remove the Interior Assembly and move the switch to the opposite direction. • Check that ...

Page 17 CONSUMER ASSISTANCE EMAIL: [email protected] WEBSITE: www.honeywellsafes.com ADDRESS: Consumer Assistance Dept. LH Licensed Products, Inc., 860 East Sandhill Avenue Carson, CA 90746 USA TELEPHONE: US/Canada 1-877-354-5457 (Toll Free) Mexico 01-800-288-2872 After English voice recording stops...