Honeywell 1101 - Installation Manual
Honeywell 1101 – Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – DIMENSIONS; CONNECTION WIRING
- Page 3 – SENSOR A; OUTPUT
- Page 4 – CALIBRATION
- Page 5 – Honeywell Building Technologies; SPECIFICATIONS
INSTALLATION INSTRUCTIONS
PW Series Conduit Wet
Pressure Transmitters
WARNING
This product can expose you to chemicals including
1,3 Butadiene, which is known to the State of
California to cause cancer and reproductive harm.
For more information, go to
www.P65Warnings.ca.gov
APPLICATION
The PWTB Series wet/wet differential pressure sensors
provide reliable, accurate measurement and control of proper
applications, including monitoring and controlling pump
differential pressure, chiller/boiler differential pressure drop,
and CW/HW system differential pressure. The PWTB Series is
ideal for measuring pressure across pumps, filters, heat
exchangers, compressors, and other non-corrosive wet media
applications. The PWTB Series of pressure sensors feature
three field selectable pressure ranges, bi/uni-directional
modes with configurable output: 4-20 mA, 0-5 Vdc, or 0-10
Vdc output.
IMPORTANT
• Only qualified trade installers should install this
product.
• This product is not intended for life-safety
applications.
• Do not install in hazardous or classified locations.
• The installer is responsible for all applicable codes.
• De-energize power supply before installation or
service.
Product Application Limitation:
Honeywell products are not designed for life or safety
applications. Honeywell products are not intended for critical
applications such as nuclear facilities, human implantable
devices, or life support. Honeywell is not liable, in whole or in
part, for any claims or damages arising from such uses.
IMPORTANT
• Do NOT exceed the gauge pressure rating of the
sensor.
• Use ONLY Honeywell gauge pressure sensors
provided with your PWTB transmitter to obtain the
specified transmitter accuracy.
• Follow instructions step by step to ensure proper
setup.
Limites de l’application du produit :
Les produits Honeywell ne sont pas conçus pour des
applications de sécurité ou de sauvetage. Les produits
Honeywell ne sont pas conçus pour les applications critiques,
comme les installations nucléaires, les dispositifs
implantables dans le corps humain ou d'assistance vitale.
Honeywell n’est pas responsable, en tout ou en partie, des
réclamations ou dommages découlant d’une telle utilisation.
IMPORTANT
• Ne dépassez PAS la pression manométrique nominale
du capteur.
• Utilisez uniquement des capteurs de pression
manométrique Honeywell fournis avec votre émetteur
PWTB pour obtenir la précision spécifiée de l’émetteur.
• Suivez les instructions détaillées pour assurer une
configuration adéquate.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Honeywell 1101
Summary
PW SERIES CONDUIT WET PRESSURE TRANSMITTERS 31-00539-01 2 DIMENSIONS Figure 1. Housing Dimensions CONNECTION WIRING Honeywell recommends 22 AWG stranded, and four conductor shielded cable to wire between the PWTB transmitter and pressure sensors. Terminals are rated for 24-14 AWG, 3.5 lb-in of torqu...
PW SERIES CONDUIT WET PRESSURE TRANSMITTERS 3 31-00539-01 IMPORTANT DO NOT attempt to plumb or tighten the sensors while wires are attached, as you risk pulling wires from cable attachments. 8. Wire sensors A & B to the PWTB Transmitter terminals labeled A & B respectively. See the table in ...
PW SERIES CONDUIT WET PRESSURE TRANSMITTERS 31-00539-01 4 15. Check remaining DIP switch (8-12) configurations for additional setup options: Display Units: LCD will display readings in PSI or kPa. LCD will indicate PSI or kPa at the top of the screen. UNI/BI: PWTB transmitter can be set up in Uni or...
