Heath Zenith 9600LED series - Manual

Heath Zenith 9600LED series

Heath Zenith 9600LED series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
Page: / 24

Table of Contents:

  • Page 2 – Wiring; recommended grounding method; Black to black; All wiring should be run in accordance with the; Contact a qualified electrician
  • Page 3 – OptiOnaL Wiring; Wiring Diagram 1 – When wiring to control a standard light fixture:; Strip the motion sensor’s red wire; master; master
  • Page 4 – FinaL assemBLy; lation
  • Page 5 – testing anD aDjustments; turn on the circuit breaker and light switch.; minute warm up period; Maximum Range; Least Sensitive
  • Page 6 – OperatiOn; Day; test; mODe sWitChing summary
  • Page 7 – trOuBLeshOOting guiDe; symptOm
  • Page 8 – tWO year LimiteD Warranty
  • Page 9 – Faroles de metal; instaLaCiOn
  • Page 10 – CaBLeaDO; CuiDaDO: nO conecte el cable rOjO; Nota; póngase en contacto; negro a negro
  • Page 11 – COneXiOn aLterna; Pele; maestra; maestra
  • Page 13 – prueBas y ajustes; Conecte el disyuntor y el interruptor de la; en medio recorrido; Lo menos sensible; Alcance Máximo
  • Page 14 – prueba; amanecer
  • Page 15 – sÍntOma
  • Page 16 – garantÍa LimitaDa De DOs aÑOs
  • Page 17 – Lanterne en métal; instaLLatiOn
  • Page 18 – CÂBLage; avertissement: ne pas raccorder le fil; Note; Contactez un
  • Page 19 – CÂBLage FaCuLtatiF; Diagramme de câblage 1 – Câblage d’un luminaire standard :; Dénudez le fil rouge du détecteur de mou-; maître
  • Page 20 – assemBLage FinaL
  • Page 21 – essais et rÉgLages; Commutateur ON TIME à TEST; Portée maximale; Le moins sensible
  • Page 22 – FOnCtiOnnement; essai; rÉsumÉ Du mODe De COmmutatiOn; PRIORITÉ MANUELLE; rÉgLage De La ZOne De
  • Page 23 – guiDe De DÉpannage
  • Page 24 – garantie LimitÉe De DeuX ans
Loading the manual

Dated receipt required for warranty replacement.

Features

• Automatically comes on when motion is detected.
• Automatically turns light off.
• Photocell keeps the light off during daylight

hours.

requirements

• The light control requires 120 volts AC.
• If you want to use Manual Override mode, the

control must be wired through a switch.

nOtiCe:

Not to be used on light dimmer or timer-

controlled circuits.

•

some electrical codes require installation by a
qualified electrician.

• This light fixture has been tested/certified us-

ing Lights of America LED Lamp Model No.
2025LEDE12.

unpaCking

Be sure to remove all contents from packaging and
verify all items are present before assembling this light
fixture. This package includes the following items:
• Lantern
• Three LED Lamps
(Lights of America Model: 2025LEDE12)
• Universal mounting bracket (X-Bar)
• Mounting hardware
• Wire nuts
• Owner’s Manual

© 2008

598-1338-03

motion sensing

Diecast metal Lantern

model: 9600LeD series

instaLLatiOn

For best performance, mount the fixture about 6 feet
(1.8 m) above the ground.
1. Remove two decorative nuts.
2. Remove X-Bar.
3. Tighten mounting screws on X-Bar finger tight.
4. Attach X-Bar to junction box.

Junction Box

X-Bar

Decorative Nut

Lantern Base

Lantern Mounting

Screw

X-Bar

Bracket Mounting

Screw

Note:

We recommend having an assistant help hold

the lantern assembly during the wiring process.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Wiring; recommended grounding method; Black to black; All wiring should be run in accordance with the; Contact a qualified electrician

2 598-1338-03 Wiring One Motion Light Two Motion Lights recommended grounding method Use a green ground “pigtail” (not provided) and twist one end together with the bare fixture wire and the box ground wire. Secure with a wire con-nector. Secure the other end of the “pigtail” with the GND screw on t...

Page 3 - OptiOnaL Wiring; Wiring Diagram 1 – When wiring to control a standard light fixture:; Strip the motion sensor’s red wire; master; master

3 598-1338-03 Black White Green or Bare Light Fixture Light Fixture (Standard) master slave Black White Green or Bare Light Fixture Light Fixture Red Red OptiOnaL Wiring This fixture is provided with a sensor rated for 360 Watts. Since the fixture is only rated 180 Watts, 180 Watts of additional lig...

Page 4 - FinaL assemBLy; lation

4 598-1338-03 FinaL assemBLy 1. Push the wires into the junction box. Make sure none of the wires get pinched. 2. Slide the fixture assembly onto the mounting screws. Tighten decorative nuts removed in step 1 of Instal- lation section securely against fixture base. Junction Box Mounting Screw Decora...

Other Heath Zenith Models

All Heath Zenith Other